Reply With QuoteVery early models are welded in
if not,after removing top slide,grip barrel and just unscrew,
BUT
make sure magazine is in situ before attempting
HIH
Pete
.
Pickle McLovin'...it's a man thing
Ok, am I missing something?
Apparently it just 'unscrews'.
How where and um.. how!
I'd love to get a replacement barrel made up with a screwcut end for a moderator... a Mak with a mod == sex
Glock 19, 43. Two ARs and a few other assorted rifles.
Registered User
Very early models are welded in
if not,after removing top slide,grip barrel and just unscrew,
BUT
make sure magazine is in situ before attempting
HIH
Pete
.
ULTIMATE KING RATTY::.22 SMK QB78DL HYBRID::+QB78 D/L .25 Cal
Pickle McLovin'...it's a man thing
Hmm. I gripped with pliers (had something between the tool and the barrel) and it didn't budge.
T03 56469 is my serial number - can't find my manual to give you a date of manufacture though.
Glock 19, 43. Two ARs and a few other assorted rifles.
Registered User
T03 = year 2003 so should be fine,Originally Posted by Napalm
grip and sharp twist to left (anti-clockwise) looking from front
will do it,keep mag in though
pliers may not get proper grip,use molegrips and lock on
atb
Pete
.
ULTIMATE KING RATTY
Pickle McLovin'...it's a man thing
Ta mate.
Mag in, roger.
I presume 'things' will fly out otherwise?
Glock 19, 43. Two ARs and a few other assorted rifles.
Registered User
I gripped the barrel in a vice after wrapping in a scrap of aluminium sheet to prevent damage then turned the grip and frame anticlockwise it loosened easily.
Banned
i followed your advice put in vice unscrewed very easy,soldered on a piece of 1/2 inch unf thread and screwed on a logun silencer.i also cut down the gas screw and drilled out the mag port and mag feed so that lead bbs can be used with no jams.
Last edited by smallholder1; 11-09-2009 at 08:39 PM.
Banned
forgot to add this pic
Last edited by smallholder1; 11-09-2009 at 08:39 PM.
Nemo me impune lacessit!!
Looks soooooooooo sweeeet
The silencer's bigger than the gun
T
UBC Secretary & Web-ManagerTHL Marksman of the Year 2010
(Airgun Section)
Pickle McLovin'...it's a man thing
how the smeg do you solder on some thread to the barrel?
Advice please, because i want a moderator on my Mak!
Glock 19, 43. Two ARs and a few other assorted rifles.
Banned
clean both surfaces bright and shiny,tin both surfaces with solder,align both parts heat untill solder melts.
Pickle McLovin'...it's a man thing
Thanks. I take it I'm not going to be using a little 25W soldering iron then!
Glock 19, 43. Two ARs and a few other assorted rifles.
Banned
blow lamp solder and flux
Registered User
Smallholder - what did you use for the 1/2" bit you soldered onto the barrel?
Does this mean that the Top Slide cannot be removed or did you cut down the originla barrel tip on a lath , so the Slide can still be slid forward and off ?
Whatever happened to the guy who posted a few posts re his intended Makarov customising service - posted pics and detaisl - some guy up in Scotland - never replies to PM's and emails - in fact last time I checked he had not been on in ages .....
" WHEN YOU'RE GOING TO SHOOT - SHOOT , DON'T TALK ! "
Banned
hi,does not interfere with slide,the thread was cut from a 1/2'' unf bolt.
Posting Permissions
