Barrel "Conditioning".

[verminhunter]

I was also told dont over clean your barrel, especially with those cleaning rods, the one with the wire bristles in particular.

You mentioned using tips for roll ups to clean the barrel, do you shoot those through or just pull them through with something?

Cheers

Just shoot them through, 5-6 just enough to take off the excess lead.
Dont use the wire brush and rod can cause damage to the rifling.

[Sam.S]

Just shoot them through, 5-6 just enough to take off the excess lead.
Dont use the wire brush and rod can cause damage to the rifling.

Ah right. thanks for the info. I've tried firing some filters through my gun and it works a treat

[u.k.neil]

Hey Costas, you took my tip on the roll-up filters then....

Neil

[verminhunter]

Hey Costas, you took my tip on the roll-up filters then....

Neil

You aint half wrong neil, thank you for that neil, took your advice and went out and bought the large filter tips, blew 3 through and yes they do work.
this is what i'll do from now on, aint going through that again.
Cheers neil.

[REEVES]

You aint half wrong neil, thank you for that neil, took your advice and went out and bought the large filter tips, blew 3 through and yes they do work.
this is what i'll do from now on, aint going through that again.
Cheers neil.

And don't forget to take your awt of first Costas as them filters will remove your baffles as well as surplas lead .

[verminhunter]

And don't forget to take your awt of first Costas as them filters will remove your baffles as well as surplas lead .

The filter tips reeves was for the .25 as its silencer is not like a awt, but I thought Id give thee old mfr a clean like the .25 and ended smashing the insides up. The mfr really reeves i usually take off the silencer and do a pull-through but saw it worked fine on the mk2 .25 id thought it would be fine for the mfr but it turned out it wasn't.

Once again reeves just would like to say a Big Thank-You for what you did for me reeves, true gentlemen mate and really appreciate it.

MFR is laser-guided accuracy I cant believe it my self, its been along time the mfr was messing around and accuracy was suffering , was never good as it was before and put it down to "too much cleaning" "barrel might be bent" "need to take it to Benny for a full service" allsorts. Then after that loud bang i just knew something was wrong, got on the blower to you, did a few findings and yes you were correct. Stuck the new AWT which is a vast improvement to the old ones and has transformed the rifle completely and i mean completely, very quiet and extremely accurate , thoughts bis mags are going on pellet on pellet at 60 yds with 1 mill dot, pellet on pellet at 50 yds cross hair, spot on.

That's how my rifle should perform and never ever in a million years would have thought the internals were swimming around every time i fired the rifle as it made no noise nor any indicating that there was something wrong until you told me what to do and look for.

Nice one Reeves top man ......and yes I will be taking off the silencer to clean from now on. Happy new Year Reeves and well done on the new AWT silencers they are extremely quiet and got to be one of the best silencers around.

[mike.watkins]

You aint half wrong neil, thank you for that neil, took your advice and went out and bought the large filter tips, blew 3 through and yes they do work.
this is what i'll do from now on, aint going through that again.
Cheers neil.

pound shop .big box , been doing this for years


why does cleaning barrels damage barrels with say pull through and cloth ?

[AlsoFishes]

Using a pullthroug can wear the crown when you pull the string accross it, usually on the same side.

[Neomagic]

Just shoot them through, 5-6 just enough to take off the excess lead.
Dont use the wire brush and rod can cause damage to the rifling.

Just a cautionary note for any spring rifle owners......don't dry fire these filter tips, although they offer some resistance, you still need to put a pellet behind the filter tip prior to firing, or you risk serious damage to your gun.

I've used these filters for ages...only 70p for 100 and they work great with youngs 303 oil.

ATB,

Chris

[verminhunter]

Just a cautionary note for any spring rifle owners......don't dry fire these filter tips, although they offer some resistance, you still need to put a pellet behind the filter tip prior to firing, or you risk serious damage to your gun.

I've used these filters for ages...only 70p for 100 and they work great with youngs 303 oil.

ATB,

Chris

Yes you are right , filter tips are only for PCPs. Dont use them on springers/ gasrams lads as you may damage the internals of these rifles, use a pull through or if you have a brake barrel just open the barrel and push a rod through it(becareful with rods).

[biglad]

i clean my 177 rapid with fag filters it works a treat

[Graeme]

Yes you are right , filter tips are only for PCPs. Dont use them on springers/ gasrams lads as you may damage the internals of these rifles, use a pull through or if you have a brake barrel just open the barrel and push a rod through it(becareful with rods).

Maybe put a pellet behind the fag tip on a springer.. just a thought..

[bmhill]

on a brand new gun would you advise cleaning the barrel then start with a type of pellet and see if you get good groups?
or not bother to clean and go straight into conditioning?

i have heard people say at least a tin (500) of pellets to condition a new gun would this be a fair assumption(sp?)?

[Rapidnick]

on a brand new gun would you advise cleaning the barrel then start with a type of pellet and see if you get good groups?
or not bother to clean and go straight into conditioning?

i have heard people say at least a tin (500) of pellets to condition a new gun would this be a fair assumption(sp?)?

Depends entirely on its accuracy 'out of the box'. If OK with pellets you expect to work in that type of rifle then don't bother.. Although rifles need a lining of lead to 'condition' the barrel a full tin is rather a lot just for leading. However, springers do take a while for all the moving parts to bed in and for the rifle to reach optimum. I'd say up to 1000 shots to see what it really can do and get it shooting really sweetly.

[bmhill]

Depends entirely on its accuracy 'out of the box'. If OK with pellets you expect to work in that type of rifle then don't bother.. Although rifles need a lining of lead to 'condition' the barrel a full tin is rather a lot just for leading. However, springers do take a while for all the moving parts to bed in and for the rifle to reach optimum. I'd say up to 1000 shots to see what it really can do and get it shooting really sweetly.

thanks for the reply
its an airwolf mct