Page 1 of 3 123 LastLast
Results 1 to 15 of 37

Thread: Inside the Feinwerkbau Model 65

  1. #1
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384

    Inside the Feinwerkbau Model 65

    Hi,

    I've started my little Feinwerkbau Model 65 project.

    This pistol has seen better days, but that was the whole point of buying it.


    I have a one already that looks like it has never been taken apart. It shoots so well that I am not about to tinker with it.

    But this one looks like it has been run over by a tractor. (Well not that bad but it needed help.)

    I have taken a lot of photos during the dismantling process, which you can find in my link below.

    http://s699.photobucket.com/albums/v...0Strip%20Down/

    I hope to describe the process in a bit more detail as I get time.

    But for now I hope the photos help anyone who NEEDS to take their Model 65 apart to change the seals or piston buffer.

    Please don't take this as an excuse to dismantle a perfectly working gun. As I have already made a tiny mistake on re-assembly and it needs to be stripped again.

    Thanks

    Mark

  2. #2
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384
    My little mistake was on the re-assembly of the rear slide bearing.

    Here http://s699.photobucket.com/albums/v..._0887Large.jpg

    It has 4 shim washers and on re-assembly I could not fit the fourth one in behind the 'E' clip on the very end to the rod. I think I may need to turn the other 'E' clip around 180 degrees to give the correct clearance.

    The result of this error is that the pistol does not fully lock when the slide is moved forwards after shooting. That tiny shim makes all the difference!

    The engineering in these really is amazing.

    Thanks

    Mark
    Last edited by Cones; 15-09-2010 at 12:10 PM.

  3. #3
    Join Date
    Jan 2007
    Location
    Prague, Czech Republic
    Posts
    1,497
    An interesting post, Mark, thanks. That looks like quite an early one - maybe late '60s/early '70s?

    Keep us informed as to how you get on!

    Matt

  4. #4
    Join Date
    Dec 2004
    Location
    North Bristol outskirts
    Posts
    1,684
    I don't think you have taken enough photos Mark, can we have a few more please

    Nice album, very useful if you have to strip one down, there's enough detail in the pics to sort out where the bit you have left over comes from.
    Everyone has a bit left over when they strip a gun.
    Don't they?.
    Surely it can't just be me, can it?
    Jef
    AKA Porthos, a Piskateer of Renown.
    I am a pistaholic, and proud of it

  5. #5
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384
    Hi,

    Yes I did get a bit carried away with the photos.

    I did not want to miss anything.

    A quick update from tonight.

    I put the pistol back together last night and took it to the club tonight to see how well it would shoot.

    The bad news is that the front sight is canted over slightly and along with the repaired rear sight it needed the full adjustment one way to bring it on aim.

    The good news it that it shoots just as well as my other 65 does. This means it is definitely worth spending some time any money on.

    The front sight removal could be difficult though, as it has been clobbered with a hammer and is well and truly stuck. I may try warming it with some hot water or air gun and see it I can twist it off the barrel.

    I should be able to get a new rear sight unit. Just depends on how much it will be.


    I will write out a stripping guide when I get the chance.

    Thanks

    Mark

  6. #6
    Join Date
    May 2004
    Location
    Truro
    Posts
    4,394
    I thought the foresight was gummed up by the rather copious paint job.

    The other thing that doesn't help is the notch on the rearsight plate being cut offset!

    Had I kept it I was thinking along the lines of getting someone like UKNeil to make an adaptor that fitted in place of the rearsight to take a small red dot sight and shroud the barrel.

  7. #7
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384
    Quote Originally Posted by rockdrill View Post
    I thought the foresight was gummed up by the rather copious paint job.

    The other thing that doesn't help is the notch on the rearsight plate being cut offset!

    Had I kept it I was thinking along the lines of getting someone like UKNeil to make an adaptor that fitted in place of the rearsight to take a small red dot sight and shroud the barrel.
    Morning.

    Yes, the paint was gumming it all up a bit. But after the Nitromors then the hammer marks became a bit more obvious.

    I've been soaking it in a penetrating oil and will try warming it up before I try again.

    It does look like at some point in its life it had the barrel weight fitted to it. There is a circular mark on the top slide where the barrel inserts.

    I did consider a red dot as well, the rear spring mounting hole looks like a good point to fix a bracket to. It could be made a snug fit on the side walls.

    If I can get the front sight off, I was thinking some carbon tube might finish off the barrel.


    I have now fixed the recoil slide problem, The 'E' clip was turned round and when installing the end shim and other 'E' clip I pushed the locking bar down a little to push against the pin a bit more and this made it easier to fit the parts.
    It now locks up perfectly each time.

    Thanks

    Mark

  8. #8
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384
    Before and after the Nitromors.

    It actually made a fizzing sound as it ate through the paint.

    http://s699.photobucket.com/albums/v..._0832Large.jpg

    http://s699.photobucket.com/albums/v..._0952Large.jpg

    Mark

  9. #9
    Join Date
    Dec 2004
    Location
    North Bristol outskirts
    Posts
    1,684
    Try sticking it in the freezer overnight (preferably when 'er indoors aint lookin'), stick a pan of water on the stove and bring to the boil, pop the foresight in the water for a few seconds and see if you can knock it off with a lump of hardwood or a hide mallet.

    It's worked on bike bits in the past.
    Jef
    AKA Porthos, a Piskateer of Renown.
    I am a pistaholic, and proud of it

  10. #10
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384
    Quote Originally Posted by jefL View Post
    Try sticking it in the freezer overnight (preferably when 'er indoors aint lookin'), stick a pan of water on the stove and bring to the boil, pop the foresight in the water for a few seconds and see if you can knock it off with a lump of hardwood or a hide mallet.

    It's worked on bike bits in the past.
    Funny you should say that.

    I have tried tonight by poring boiling water over it then clamping it in the vice between two wood blocks.

    It won't budge.

    I may try and see if I can obtain a new front sight block, because I don't think this one will come off without the use of a hacksaw on it at the moment!

    After the struggle with the front sight I removed the rear sight and set about it very carefully with my needle files. The rear notch is now a lot better than it was. I did the top edge on a sheet of wet and dry resting on a glass sheet. It is still at two different levels were it has been welded up. But now the top edge is better than it was as well.

    I have now refitted it and blacked it with some soot from a lighter. The sight picture is now half decent.

    The grip is an after market one made by Nill http://www.nill-griffe.com/ The bottom screw would not tighten up and tonight I found out why. The nut was on the same side as the screw? So I have removed it and put the nut back on the correct side, now it tightens up properly.

    More pictures in a while.

    Thanks

    Mark

  11. #11
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384
    This is now the rear sight with a little careful filing.

    http://i699.photobucket.com/albums/v...p2010Large.jpg

    Finished for the moment.

    http://i699.photobucket.com/albums/v...p2001Large.jpg

    A few Targets from Wednesday at the club.

    http://i699.photobucket.com/albums/v...p2012Large.jpg

    http://i699.photobucket.com/albums/v...p2013Large.jpg

    http://i699.photobucket.com/albums/v...p2014Large.jpg

    http://i699.photobucket.com/albums/v...p2015Large.jpg

    http://i699.photobucket.com/albums/v...p2016Large.jpg


    Over the Skan chrono at the club it was doing about 450-460 fps with RWS R10 Match. On the Geco's it was about 30 fps slower with a bit more variance. It seemed to shoot well with either though. I mixed up the targets and cannot remember which was which!

    I'll try again this time inside tomorrow with the fixed sights, grip and slide locking mechanism and see if it gets any better.

    Thanks

    Mark

  12. #12
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384
    I was trying to get a better idea of the manufacturing date of this particular model 65.

    I found this statement on another forum.

    Ulrich Eichstädt

    Before 1972, when the first (after-war) german gun law was introduced, it wasn't necessary to number airguns like firearms (some manufacturers did, others didn't). Also the early FWB pistols (before 1972/73) don't carry the "F in pentagram"-sign, which is required now to show that an airgun has less than 7,5 joule muzzle energy (around 5.5 ft/lbs, only in germany).

    Although it wasn't really necessary to mark the "F" on air pistols (and air rifles) for export, it is possible that due to the more easy way of manufacturing that all models are marked.

    So IF you have a FWB 65 with an F, it was made after 1973 (the year the F-mark was used first, even though it was introduced before)

    The quote "RA" in the e-mail's head stands for Rainer Altenburger, the sales manager (and co-owner), who surely knows what he says (but of course he could make mistakes, anyway, too...)





    My pistol serial number 30307 does have the F mark shown on it so it could be around 1973-1974 as it is a lowish serial number.

    F-Mark
    http://i699.photobucket.com/albums/v..._0830Large.jpg

    Serial Number
    http://i699.photobucket.com/albums/v..._0833Large.jpg

    Thanks

    Mark

  13. #13
    Join Date
    Jan 2007
    Location
    Prague, Czech Republic
    Posts
    1,497
    Quote Originally Posted by Cones View Post
    I was trying to get a better idea of the manufacturing date of this particular model 65...
    Garvin gave me some useful dating info on this thread. There's also a good thread on the AVA forum here.

    Please keep us posted on your progress, Mark. Anything FWB related is always worth a read (great website you have there, by the way).

    Matt

  14. #14
    Join Date
    Jul 2009
    Location
    Reigate
    Posts
    188
    Good stuff Mark. Some useful and informative photographs.

    You may find some information to help with dating on the Yahoo group FWB Model 65 Airguns

  15. #15
    Join Date
    Apr 2005
    Location
    Grantham
    Posts
    1,384
    Quote Originally Posted by Nikkormat View Post
    Garvin gave me some useful dating info on this thread. There's also a good thread on the AVA forum here.

    Please keep us posted on your progress, Mark. Anything FWB related is always worth a read (great website you have there, by the way).

    Matt
    Thanks.

    That date thread helps a lot.

    # 72,294 has been manufactured in June 1975

    So with the 'F' mark only after 1973 and my serial number of 30307 it makes my pistol around the 1974 point with reasonable certainty.

    Thanks

    Mark

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •