Page 2 of 6 FirstFirst 1234 ... LastLast
Results 16 to 30 of 77

Thread: Mainspring data thread

  1. #16
    Join Date
    Jul 2004
    Location
    cardiff, south wales.
    Posts
    3,368
    New HW80: 28 coils 3.1mm wire 21mm OD 240mm long.

    John
    Law of any kind only affects those willing to abide by it.

  2. #17
    Join Date
    Mar 2009
    Location
    Atascadero, CA USA
    Posts
    348
    Quote Originally Posted by bigtoe01 View Post
    I like this spring..a LOT, if Walther will push LGV spares into the UK I for see this spring being used in many project guns.

    Specs are:

    236mm long, 3.35mm wire, 20.8mm OD, 14.4mm ID, 3.96mm between coils, 33 coils.

    If the rifle you are tuning is optimised this spring will deliver 11fpe in .177 with ease with just 34CC of swept volume and the shot cycle is supreme. Its a soft spring due to the 33 coils but packs a nice punch.

    Titan should make a copy of this one
    Re-reading this statement Tony... define 'optimised' here. I think you said it didn't work well in a TX. Just not enough room in that gun to pre-load it properly? What kind of rifle would it be good for? I ordered one of the 16J kits from Germany and I'm going to test the piston in my TX but would like to hang onto the spring if there is a good use-case for it. Maybe an HW95 at 12fpe? At 34CC would a .22 be best?
    Good deals: davida6212 jimmer u.k.neil

  3. #18
    Join Date
    Mar 2009
    Location
    Atascadero, CA USA
    Posts
    348

    Which of these look promising for a TX200 sub 12fpe with short stroke?

    I currently have the QX4600 - in a gun with Mk1 stroke it's up near 11.7 ft lbs with no top hat and no spacers....just custom guide. So there really is no spacing option. It would be nice to be able to adjust pre-load some more...I can't go up with this one. The piston is lightened as well.

    Here are some other Maccari springs that I can easily source here in the U.S. (some may not fit the TX factory guides though and will need custom ones):

    QX4600 spring 32 coils x.120" wire - ID .560 set
    http://www.airrifleheadquarters.com/...88/7905117.htm

    R6 Ultra XLD spring 30 coils x .120" with .530 ID
    http://www.airrifleheadquarters.com/...88/1979288.htm

    E9870 Euro Universal spring 39 coils x .120" wire 480" ID - 13" OAL
    http://www.airrifleheadquarters.com/...88/6825218.htm

    E8700 mini spring .105 wire, 29 coils, ID .555" 10" OAL
    http://www.airrifleheadquarters.com/...88/5730289.htm

    Merlin XL spring - Square wire, figure it at .116" average, .509 inch ID., 37 coils and 12.2" plus unset.
    http://www.airrifleheadquarters.com/...88/4452198.htm

    E3200 spring 32 coils, .110 wire, ID .540 inch - Unset 12" OAL
    http://www.airrifleheadquarters.com/...88/7908088.htm

    Merlin Mini Mag spring 29 coils x .110 round wire x .545 ID
    http://www.airrifleheadquarters.com/...88/9682441.htm
    Good deals: davida6212 jimmer u.k.neil

  4. #19
    Join Date
    Apr 2012
    Location
    Retford, Notts
    Posts
    34,740
    Chaps,

    To tie in with Airsporter 1st's thread on HW80 mainspring spec, I thought this'd be of relevance, again.....
    THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
    NEXT EVENT :- May 4/5, 2024.........BOING!!

  5. #20
    Join Date
    Apr 2012
    Location
    Retford, Notts
    Posts
    34,740
    Only me!!!!!

    Just thought I'd ping this thread back up, to tie in with that excellent current thread on different springs and springer tuning!!

    Jim, could this go into the "Useful Info" section, yet?

    Ciao,

    Tone.
    THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
    NEXT EVENT :- May 4/5, 2024.........BOING!!

  6. #21
    Join Date
    Apr 2002
    Location
    Near Wimbledon, SW London, or Lusaka, Zambia
    Posts
    26,322
    As I've run out of springs for my mk2 stroke TXs, I'm going to buy a #1 and #9 titan to try, based on the info is this thread they should both be suitable. In fact I think the #1 should be perfect

    Thanks again for posting...

  7. #22
    Join Date
    May 2008
    Location
    Wingham, 5 miles NW of Baz
    Posts
    5,660
    Quote Originally Posted by Jon Budd View Post
    As I've run out of springs for my mk2 stroke TXs, I'm going to buy a #1 and #9 titan to try, based on the info is this thread they should both be suitable. In fact I think the #1 should be perfect

    Thanks again for posting...
    I stuck a number 1 Titan in my .177 Diana 52 and it made 17 ft lb. I had to cut 3 whole coils off it to get 11.4 ft lb

    Bloomin stiff spring

    I'll be interested to hear how it goes john and how many coils you end up lopping off

    Matty
    Opportunity is missed by most people, because it is dressed in overalls and looks like work.

  8. #23
    Join Date
    Oct 2009
    Location
    Stockport
    Posts
    6,058
    Jon

    what length spring and what coil count and wore thickness do you need?

  9. #24
    Join Date
    Apr 2002
    Location
    Near Wimbledon, SW London, or Lusaka, Zambia
    Posts
    26,322
    Quote Originally Posted by bigtoe01 View Post
    Jon

    what length spring and what coil count and wore thickness do you need?
    I want ~ 3.2mm wire, around 21 - 21.4 OD
    Coils and length is the experimentation - I want a few more coils, and a little more length, to get an overall softish but not too soft and unstable spring. I need to measure lenght, but obviously if I go a bit long it's easy enough to trim. #1 looked a good spec.
    Last edited by Shed tuner; 02-12-2013 at 11:11 PM.

  10. #25
    Join Date
    Apr 2002
    Location
    Near Wimbledon, SW London, or Lusaka, Zambia
    Posts
    26,322
    Quote Originally Posted by MattyBoy View Post
    I stuck a number 1 Titan in my .177 Diana 52 and it made 17 ft lb. I had to cut 3 whole coils off it to get 11.4 ft lb

    Bloomin stiff spring

    I'll be interested to hear how it goes john and how many coils you end up lopping off

    Matty
    hmmm... chopping is easy, but I don't want it too stiff... it looked less stiff than the #9 (more coils, same len), and the #9 is meant for a mk2. Maybe I should try the #10 but it looks too thin wire and possibly a bit short

    Is the #1 really stiff, or just too long ?

  11. #26
    Join Date
    Aug 2009
    Location
    Hessle. East Yorkshire
    Posts
    256
    Hi all

    Just thought I would add this to the mix.

    One of the guys I shoot against is running a titan No7 in his tx with good results.
    I shot it & it felt very fast but a little harsh for my liking, all other internal details he seems reluctant to divulge.
    Have any of you tried one before I waste my money.

    Regards Jon

  12. #27
    Join Date
    Aug 2009
    Location
    Hessle. East Yorkshire
    Posts
    256
    I tried the 9 in my set up & it made power very easily, so much so I had to cut a few coils off.

    With minimal top hat the spring has only 5mm preload which gives me 11.2-11.3 f/lb.( also gets a bit stiff to cock towards the end but not excessive )

    The number 10 had 47mm preload to make 11.2f/lb

    Jon

  13. #28
    Join Date
    Dec 2011
    Location
    coventry
    Posts
    1,750
    I use the No 9 and the Mk2 in my guns depending on stroke, the No 9 is good and makes power easily but is a bit stiff to cock, I would like something in between ideally

  14. #29
    Join Date
    Aug 2009
    Location
    Hessle. East Yorkshire
    Posts
    256
    Nick

    I was a bit concerned that with so little preload that it would not keep the bounce in check, but it seems to shoot fine @ 25 yards, of to test it out to 55 this morning.

    Jon.

  15. #30
    Join Date
    Dec 2011
    Location
    coventry
    Posts
    1,750
    Quote Originally Posted by airborn68 View Post
    Nick

    I was a bit concerned that with so little preload that it would not keep the bounce in check, but it seems to shoot fine @ 25 yards, of to test it out to 55 this morning.

    Jon.
    Mine( TX200) has a very light piston, and that does not bounce with the No 9, I do have a bit more spring room than standard though.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •