My little review on the hammerli ar20ft

[Hawkeye20]

Hello, there isn't many reviews on this rifle so I thought il make a little one, I done a deal with a friend and I ended up with a hammerli ar20ft that I have wanted for a while, sat down with it before I done the deal and I was very impressed with the accuracy of the gun, I have since tuned the internals by polishing certain parts and removing all the burs from moving parts. I put it over a chrono and very very consistent and nice and easy to take apart. As it's regulated you get a pretty good shot count 170 shots per fill from 300 bar

down side is the plastic grip and hamster in which I will find someone to make me some wooden ones and the matt finish on the aluminium stock gets dirty to easy so that will be sprayed when I have time.

That's pretty much it and very happy with seems to be a cheap but very consistent accurate rifle

[Rich]

I'm very impressed with mine too. The first one I tried, when they were launched, was not all that nice to handle, But this one has had a few alterations done.

A couple of weeks ago I tried some long range bench resting with it and managed to get four pellets to string into one traffic light hole at 80 yards. The EV2 that this rifle replaced never gave me this standard of accuracy.

[Hawkeye20]

I'm very impressed with mine too. The first one I tried, when they were launched, was not all that nice to handle, But this one has had a few alterations done.

A couple of weeks ago I tried some long range bench resting with it and managed to get four pellets to string into one traffic light hole at 80 yards. The EV2 that this rifle replaced never gave me this standard of accuracy.

Glad I'm not the only on that has one and think they are very good

If you ever have any questions about tuning the ar20ft then give me a shout

[scubaman]

Well happy with mine as well. Managed to pick up one 4 months old for a song.

Only mods done to mine are cosmetic really....
Had the shroud milled away but NOT for any POI shift issues but so I could fit the UK Neil air stripper I found on a certain auction site.
After the milling was done then a simple carbon wrap on the barrel for protection.
Next is a 3D printed adjustable butt pad , again from the same auction site.
Butt hook made for it as well.

As to accuracy, a fellow club member picked it up and shot a three shot cloverleaf group at 55 yds , to say he was impressed is an understatement.

Cheers,
Scubaman.

[Hawkeye20]

I want laminate grip, hamster and cheek piece but can't find anyone that would make some

[Hawkeye20]

Went out with my ar20ft and put the silencer on and zeroed in and still amazed how unbelievably accurate it is, can't wait for Hft round tomorrow and see how I get on with it then

[Hawkeye20]

Well happy with mine as well. Managed to pick up one 4 months old for a song.

Only mods done to mine are cosmetic really....
Had the shroud milled away but NOT for any POI shift issues but so I could fit the UK Neil air stripper I found on a certain auction site.
After the milling was done then a simple carbon wrap on the barrel for protection.
Next is a 3D printed adjustable butt pad , again from the same auction site.
Butt hook made for it as well.

As to accuracy, a fellow club member picked it up and shot a three shot cloverleaf group at 55 yds , to say he was impressed is an understatement.

Cheers,
Scubaman.

Have you got any pictures of yours as I was thinking of removing the shroud and getting the barrel threaded

[pruddasfinest]

Just fitted the wood from Warren Edwards.
Photos really dont do these justice.
The grip needed a bit of modding to make it fit, no big deal, easy to do. The guns not finished yet and will look a lot smarter when its done but the wood is a big step in the right direction.

[pruddasfinest]

Got the wood from Warren yesterday. The grip took a bit of work at the back to fit but nothing major and wasn't too hard.