Results 1 to 13 of 13

Thread: BSA Underlever Cocking link needed.

  1. #1
    Join Date
    Dec 2012
    Location
    Bristol
    Posts
    1,116

    BSA Underlever Cocking link needed.

    Hi chaps, these seem to be a bit like hens teeth but here goes.
    Bsa standard 1934/35. Cocking link needed. If it wasn't for the fact it is missing I would give you the length. Have been told it should be 209mm??
    Have tried Protek, Knibbs etc. with no sucess, any suggestions or help gratefully recieved.
    With thanks.
    Cheers.
    Geoff.

  2. #2
    Join Date
    May 2006
    Location
    Surrey
    Posts
    8,554
    Quote Originally Posted by Geoff555 View Post
    Hi chaps, these seem to be a bit like hens teeth but here goes.
    Bsa standard 1934/35. Cocking link needed. If it wasn't for the fact it is missing I would give you the length. Have been told it should be 209mm??
    Have tried Protek, Knibbs etc. with no sucess, any suggestions or help gratefully recieved.
    With thanks.
    Cheers.
    Geoff.
    POD at BFTO maybe

  3. #3
    micky2 is offline The collector formerly known as micky
    Join Date
    Jan 2016
    Location
    boston
    Posts
    2,134
    They sometimes turn up on E**y

  4. #4
    edbear2 Guest
    Hi, can you give me a diameter of the bearing area of the screw that goes though the push button front arm, ie. the front pick up point for the missing arm (which I assuming latches into the cocking slot at'other end).

    reason is the 1930's saw some detail changes etc.

    ATB, ED

  5. #5
    Join Date
    May 2006
    Location
    Surrey
    Posts
    8,554
    Quote Originally Posted by Binners View Post
    POD at BFTO maybe
    Ignore post above (wrong geoff)

  6. #6
    edbear2 Guest
    Quote Originally Posted by Binners View Post
    Ignore post above (wrong geoff)
    Silly old goat!

    ATB, Ed

  7. #7
    Join Date
    May 2006
    Location
    Surrey
    Posts
    8,554
    Quote Originally Posted by edbear2 View Post
    Silly old goat!

    ATB, Ed

    Correct on three counts

  8. #8
    Join Date
    May 2006
    Location
    Surrey
    Posts
    8,554

    Another cocking link wanted

    While you fine chaps are rummaging to find Geoff a cocking link, should you stumble across one for the early BSA break barrel (B series), please let me know.

  9. #9
    Join Date
    Dec 2012
    Location
    Bristol
    Posts
    1,116
    Hello everybody, thank you for all your help, Ed I will let you know ASAP the rifle is 40 miles away at the moment, I will have to wait for my son to pick it up for me.
    Cheers.
    Geoff.

  10. #10
    edbear2 Guest
    Hi Goeff, have one here which is 7.5 inches from centre of pivot hole to rearmost end of part which engages in the piston slot...ie this dimension is it's ''working'' length, front hole is 0.191" if any good P.M. me a destination and it's yours

    ATB, ED

  11. #11
    Join Date
    May 2006
    Location
    Surrey
    Posts
    8,554

    Martin pm

    In box full sir

  12. #12
    Join Date
    May 2006
    Location
    Surrey
    Posts
    8,554
    Quote Originally Posted by edbear2 View Post
    Hi Goeff, have one here which is 7.5 inches from centre of pivot hole to rearmost end of part which engages in the piston slot...ie this dimension is it's ''working'' length, front hole is 0.191" if any good P.M. me a destination and it's yours

    ATB, ED
    PM on its way, thank you

  13. #13
    Join Date
    Dec 2012
    Location
    Bristol
    Posts
    1,116
    Hello ED Many thanks, PM on way. Sorry for any delay, internet intermittant.
    Kind regards.
    Geoff.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •