Longbow strip down

[Clanchief]

Hi Archie,

Yes that is the fiddly bit, once its in and the safety can slide/move etc, release the trigger and it should cock, as I said its weird just like Jonny said also, so try it a few times with no spring etc.

The manual is available here

http://spares.bagnallandkirkwood.co....bow_Manual.pdf

[archie]

Many thanks, I will be having another look at it over the next few days.

[archie]

Well, spent another afternoon trying to sort this bl***y rifle. In the end I managed to cock it, but really had to slam the barrel back into the cocking position. Obviously no good like this. All the parts look in perfect condition, trigger, piston etc. Such a shame as it`s a lovely rifle sitting in a walnut stock and very accurate when it works.
I`ve just assembled it and put it in the gun cabinet as I am really peeved off with it at the moment.

[TopDog]

Well, spent another afternoon trying to sort this bl***y rifle. In the end I managed to cock it, but really had to slam the barrel back into the cocking position. Obviously no good like this. All the parts look in perfect condition, trigger, piston etc. Such a shame as it`s a lovely rifle sitting in a walnut stock and very accurate when it works.
I`ve just assembled it and put it in the gun cabinet as I am really peeved off with it at the moment.

Hi Archie

I understand your frustration and my apologies for not spotting your thread earlier (Mach 1.5 gave me the heads-up!).

You have discovered the need to set the trigger before installing but, assuming that nothing has been added internally, the only thing left is the arrest of the intermediate sear SR134. This is usually implemented by a collar (Sear Stop Bush W198) around the trig block retaining screw. The numbers refer to the Chambers diagram at

https://www.gunspares.co.uk/products/24531/Longbow/

If all this gets you nowhere, don't panic as they are well worth having when sorted! Give me an e-mail and I will help all I can!

I can send a dimensioned diagram of the internals since I prepare them for all models I strip and note differences, where they exist, in all samples!

Sounds like you have the makings of a fine rifle there! They are certainly my choice for a medium weight barrel cocker!

atvb
David

[Mark A]

Looks like the part you mentioned is out of stock on Chambers . I have a Tomahawk and do worry what I am going to do if anything breaks and need replacing as a lot of the parts are lno longer available. Hope Archie can get a replacement made up if its just a simple part thats missing.

[TopDog]

Looks like the part you mentioned is out of stock on Chambers . I have a Tomahawk and do worry what I am going to do if anything breaks and need replacing as a lot of the parts are lno longer available. Hope Archie can get a replacement made up if its just a simple part thats missing.

The retaining collar is just a short tube so no bother. It often drops off when removing the stock! If that is the problem, I will measure one and draw up diagram a replacement! I got fed up with these dropping off and designed a new replacement for the retaining screw assembly which includes an integral collar. Have since thought up an easier solution but haven't tried it yet!

I had contemplated adding a stop to the trigger housing since that is where the problem lies!

These are the little things which make life with out-of-production models so interesting! No different from vintage cars etc!

Oh by the way, I have 5 BrumBows in various guises and two special Tomahawks (a V-Mach Cobra and a Venom Sidewinder) so potentially many special bits and pieces!

Happy airgunning!

atvb
David

atvb
David

[archie]

Thanks David, eventually come to the conclusion that this is the problem. The block retaining bolt does look as though it has an integral collar, but I will pull the stock off again to double check. I did check the Chamber`s web site but it`s not too clear. Was the original collar free to drop out before the bolt was removed from the trigger block. If so it would seem that I have a missing part.