Page 2 of 2 FirstFirst 12
Results 16 to 21 of 21

Thread: Walther CP3 - problem with co2

  1. #16
    Join Date
    Jan 2009
    Location
    christchurch
    Posts
    7,130
    [QUOTE=Discocom;7412860]Many thanks for all the advice. I wonder if the cylinder was slightly overfilled, which caused the problem as working fine now.



    Sorry I was a bit terse there.

    An overfill can give the hammer too much pressure to overcome causing failure to fire.
    Check the weight of the cylinder,usually indicated on the side.
    On my FWB you can let a bit of co2 out if you have overfilled.

  2. #17
    Join Date
    Mar 2010
    Location
    Rossendale and Formby
    Posts
    5,595
    Quote Originally Posted by Discocom View Post
    Many thanks for all the advice. I wonder if the cylinder was slightly overfilled, which caused the problem as working fine now
    I have owned several CP1, CP2 and CP3 pistols and have also had a mystery leak now and again that has sealed itself too.

    This usually followed a period of non-use and is one of the reasons why I always try to exercise all of my pistols and rifles as often as possible - leaving them unused does not do them any good at all!
    Rossendale Target Shooting Club. Every Tuesday and Thursday evening 7 - 10pm.

  3. #18
    Join Date
    May 2010
    Location
    Bognor Regis
    Posts
    1,165
    Quote Originally Posted by nige346 View Post
    These are the sizes you'll need

    Valve seal 6.0 x 2 xxxx OPN 2490021
    Bolt 4.0 x 1 OPN 2472309
    Barrel seals 9.0 x 1.5 OPN 2472295
    Cylinder Seal 14.0 x 3 xxxx OPN 2459817
    Cylinder fitting 15.0 x 2 OPN 2476266

    OPN = Original part number
    xxxx = These must be Polyurethane as in constant CO2 contact
    Many Thanks for the information. I have a couple of cylinders i need to reseal. at the moment I am using my good CP2 cylinders on all the CP series pistols they fit on.
    I looked at the seal force website and they didn't seem to do any polyurethane o rings at least not on there eb-y store
    FWB P8X,Hammerli AP40, Steyr LP1 Walther LPM-1, CPM-1, CP1, CP2, LP3, LP53, LP300, LP400, Terrus, Pardini P10, FX Wildcat .177, HW100 .22, AA S410 .22, BSA R10 MK2 .177, , HW77, 80, 90 BB AK47, S&W 586 and more blow back Co2 BBs than you can shake a stick at

  4. #19
    BigEars Guest
    If the CO2 is in a liquid state it will need some head space to evaporate into to provde gas pressure. If you're over full then the head space will be insufficient for enough evaporation to take place between shots.

  5. #20
    Join Date
    Apr 2017
    Location
    london
    Posts
    213
    Thanks again for the seal advice, will pop into Protek next time I’m down that way (any excuse!)

  6. #21
    Join Date
    Jan 2003
    Location
    Ringwood
    Posts
    4,927
    Mark, the link to the o-ring people doesn't show and polyurethene rings.
    Remember, it is the strongest character that God gives the most challenges.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •