Can you are 4 mates not try it?
It sounds a bit tight to me, but I see range mats are only 80cm.
We are trying to make our local range 5 prone lanes. The width of the range is 5.2m do you think just over 1m each is sufficient please. Thanks
Can you are 4 mates not try it?
It sounds a bit tight to me, but I see range mats are only 80cm.
Looking at ISSF regulations I can't find 25m prone.
But it says a 50m prone must be 1.25m.
But a 10M pistol can be 1.0M
And 25M pistol is 1.5M for rapid and 1.0M for standard pistol.
This is the link I have.
https://www.knsa.nl/media/1999/issfr...hprint-eng.pdf
And it was 2013/4 so could have changed.
I'd ring the NSRA on Monday.
looepete,
As we are a Home Office Approved Club that uses military ranges, we subscribe to JSP-403 :
Air Rifle Range :
https://www.gov.uk/government/upload...ap26_DLRSC.pdf
25 m indoor range :
https://www.gov.uk/government/upload...ap03_DLRSC.pdf
Tube range :
https://www.gov.uk/government/upload...ap11_DLRSC.pdf
Have fun & a good Sunday
Best regards
Russ
The simple answer is no.
Russ has given you the widths you will need to get range certification, minimum 1 mt per lane for small bore rifle, but that is cutting it really fine for a good target range, and it will be very borderline for certification, possibly not accepted.
The ISSF rules are a better guide for usable target points for prone, of min 1.25 mt, the matt under ISSF is 80 mm, so the 1.25 allows the matt to be angled one way for right handers, and the other for the cursed lefties.
We've all shot on squeezed up prone ranges, not good at all, most good prone shooters use every bit of the 1.25 mt's, (and some more!), you could possibly squeeze 5 points in, but not a good idea, it will be a much better and nicer to shoot on range with 4 points.
Have Fun
Robin
Walther KK500 Alutec expert special - Barnard .223 "wilde" in a Walther KK500 Alutec stock, mmm...tasty!! - Keppeler 6 mmBR with Walther grip and wood! I may be a Walther-phile?
Obviously worth noting that though the NRA/NSRA Construction Handbook is largely cribbed from JSP403, there are nuances and the military guides should only be taken as a guide for civilian ranges, not the definitive last word (but they're free and a decent starting point!).
Sorry, but it's significantly more nuanced than "no".
Our range was recently recertified and the prone points are a smidge less than 1metre. They also converge - the target end of the range is only about 3.5m wide!
1.25m is the ISSF standard and the "ideal", but most ranges make do with less. The military want a metre, and it sounds like they will just about squeeze into that with 5.2m for a 5-lane range.
Moreover, I've never come across a range with the "required" raised firing point outside of cadet/military ranges. What applies to the military is not always taken as gospel for civvie ranges.
0355. Firing Points. When firing is conducted from the prone position on just one firing point a raised platform approximately 450 mm high should be provided. This reduces the possibility of ricochet from low shots hitting the range floor. It may be built into the range floor or be a free standing structure. It should be about 2.5 m from front to rear with a fall of 1:12 from the front
edge.
"A fear of weapons is a sign of retarded sexual and emotional maturity." Sigmund Freud
Shooting is my meditation