I use 3.2 gr of Herco in my Alfa MLR and never had any issues but it does kick quite hard so I was thinking of dropping to 3 gr, 148 grm WC btw.
I use 3.2 gr of Herco in my Alfa MLR and never had any issues but it does kick quite hard so I was thinking of dropping to 3 gr, 148 grm WC btw.
First of all, some links to a few pictures of my Ruger Old Army nitro conversion revolver which allows me to load the gun with the cylinder in place rather than having to remove it to load using a small press which is normally the case on UK conversions or purpose made muzzle loading nitro revolvers.
https://i.imgur.com/33xXWRNl.jpg
https://i.imgur.com/p5SEooyl.jpg
https://i.imgur.com/8L92G2el.jpg
https://i.imgur.com/p5SEooyl.jpg
I tried increasing the load in small increments from 5 to 6 grns of Herco at the range today. The heavier loads grouped higher, but still suffered from the presence of some unburnt powder with the occasional light discharge. A definite improvement this time though as the 5 grn load grouped into 4" at 25yds unsupported with the fewest light discharges. I will now try a faster powder and some .460 ball to see if things can be further improved.
Regards
Brian
Last edited by Abasmajor; 18-05-2018 at 03:54 PM.
I think I know what your problem is.
You do not compress blackpowder but you do need to compress smokeless to achieve good ignition. Blackpowder is consumed almost immediately on ignition, which is why it is classed as an explosive and it will explode when unconfined. Smokeless powder will not, it only burns with a very fierce flame. It needs to be held back for a fraction of a second because it generates pressure very quickly but needs time to do this.
An example of this is from when I used to reload shotgun cartridges and may help you understand it better.
For a shotgun cartridge to function correctly so it gives a clean powder burn the crimp, (or rolled turnover), has to hold the powder back long enough for it to start generating pressure. Sometimes if a paper cartridge case was used too many times the paper at the mouth would become soft and the crimp would not be tight.
What happens is that on ignition the shot and wads start to move before the pressure has built up and the powder charge funnels up the barrel with just the outside portion burning. When it gets out of the barrel into the atmosphere it burns rapidly and goes "bloop". Hence the term a "Blooper" (You may not of heard of this now paper cartridges are rare). The shot usually falls to the ground well short of its intended target and has no energy. Because a clean burn has not been achieved there is usually a lot of residue left in the barrel.
Centrefire ammunition works differently so the powder does not need to be compressed. The resistance of the bullet in the case neck and the resistance of the bullet passing through the rifling have the same effect of holding back the charge.
I would look at using a wad under the ball so the powder needs to be compressed when the ball/bullet is pressed into the chamber. The tighter fitting bullet will obviously help as well.
I would also try different primers and check the nipples are clear with no unburnt residue or burrs that can impede the jet of flame into the powder charge.
Hi,
Problem solved with the use of 2.9 grns of Bullseye instead of the previous 4.5 grns of Herco.
Interestingly, the point of impact was the same as with the Herco load, but without the inconsistent performance and no evidence of unburnt powder.
Regards
Brian
Is there any noticable recoil with such a small load of powder and have you chronod it ?
This load was the same one that I used when shooting .38 SPL and a 148 grn HBWC bullet before the 1995 breech loading pistol ban and the recoil feels about the same as far as I can remember. It's now my intention to gradually increase the load up to a maximum of 3.5 grns to see what effect if any this has on accuracy, although I'm sure this will improve once I re familiarise myself with the pistols handling characteristics.
Brian
Hello Steve,
Although ignition reliability improved with Bullseye, I would prefer to use a larger flake powder which would not leak through the primer pocket holes.
In addition to this, I was still getting too many weak discharges for my liking, so I now limit the Ruger to 777 substitute powder which ignites every time with consistent velocity. I'm not really sure why the Ruger has been troublesome as my Anvil Remington 1858 conversion has been entirely reliable with the recommended Herco smokeless powder.
Brian