Page 1 of 3 123 LastLast
Results 1 to 15 of 34

Thread: Daysate Servicing

  1. #1
    Join Date
    Mar 2007
    Location
    Darlington. The Land of the Prince Bishops Durham
    Posts
    1,036

    Daysate Servicing

    Have a Daystate Mk4 (non "TV" screen model !!). Could do with a service. Has started scattering shots on a target even when bench rested.
    Aware only certain places, apart from Daystate, where they can service these guns. Would appreciate contact info for a company located "up north". Nearer Co. Durham the better of course who could carry out a service.
    What is the likely cost ???.

    Thanks
    Regards
    Al.
    AlBur
    Always Remember "Utopia Does NOT Exist"

  2. #2
    Join Date
    Jul 2003
    Location
    Leek
    Posts
    383
    Dunno about oop north but Staffordshire Custom Rifles are always said to be the best, dunno about prices but if you rang Dave would let you know.

  3. #3
    Join Date
    Sep 2014
    Location
    Aberdeen
    Posts
    651
    It's all relative; to me, Darlington is many hours South.

  4. #4
    Join Date
    Apr 2014
    Location
    Northallerton
    Posts
    215
    It’s a trek, but Pickering Guns would do it

  5. #5
    Join Date
    Aug 2012
    Location
    heswall
    Posts
    1,520
    may not need a service,could be other factors causing inaccuracy

  6. #6
    Join Date
    Oct 2009
    Location
    aberdeenshire
    Posts
    25,209
    Quote Originally Posted by zephyr View Post
    It's all relative; to me, Darlington is many hours South.
    Livelines in Armadale is the most local to us up in Aberdeen/shire I think .

    https://www.airgundealerscotland.co.uk/

  7. #7
    Join Date
    Oct 2017
    Location
    Briston
    Posts
    106
    any dealer who is a daystate premier partner on their dealer map will have the staff and equipment to service and if needs be re-map these rifles

  8. #8
    Join Date
    Sep 2018
    Location
    Oldham
    Posts
    95
    Quote Originally Posted by woodpigeon View Post
    may not need a service,could be other factors causing inaccuracy
    Try cleaning the barrel with a pull through a lot of people recommend this when you start to lose accuracy. Might save you the time and money. 👍🏻
    HW50 Stainless, HW77k SE Forest Laminate.20, HW80 Project .22, HW100 laminate . 177,

  9. #9
    Join Date
    Mar 2003
    Location
    Farnham, Surrey
    Posts
    12,192
    Chrono the rifle-if its consistent then look at the barrel / probe alignment and if a silencer or aftermarket muzzle is fitted, check that pellet clipping is not the issue.
    Check probe seals-these can fail with age / use / leaving the gun stored with the bolt closed (which I never do on a PCP).
    Dave Brayford at SCR is the go-to-guy these days, although I am sure your local dedicated air rifle club will have someone handy as a member.
    Never go off half cocked....

    All lies matter

  10. #10
    Join Date
    Jul 2014
    Location
    Kingston Upon Hull
    Posts
    77
    Another vote from me for Dave @SCR, he's a top bloke and did a fantastic job for a very reasonable price when my Mk3 needed servicing.

  11. #11
    Join Date
    Sep 2012
    Location
    Stoke on Trent
    Posts
    116
    Friend had the same problem at the range and another shooter suggested changing the probe seal....and it was instantly a tac driver.....bloody tiny o ring made a £1000 rifle shoot like a gat

  12. #12
    Join Date
    Mar 2007
    Location
    Darlington. The Land of the Prince Bishops Durham
    Posts
    1,036

    Daystate Mk4

    Thanks for the helpful responses. Much appreciated.
    The gun is 0.20 calibre. Will the probe O-ring be calibre specific or will the probe O-ring for 0.22 calibre fit.

    O-rings readily available on bay.

    Thanks
    Al.
    AlBur
    Always Remember "Utopia Does NOT Exist"

  13. #13
    Join Date
    Mar 2007
    Location
    Darlington. The Land of the Prince Bishops Durham
    Posts
    1,036

    Thumbs down Daystate Mk4

    Fitted a new probe O-ring. No better.
    Worse still when I tried to fill it up it began leaking air at around 150 Barg. Appears to be coming from a point where barrel meets the action. Loses pressure quite quickly.

    Thought I would take it to Customguns at Hartlepool. However it would appear that he stopped accepting work in September. Showing "permanently closed" on internet.

    Anyone any further thoughts or is it a hefty bill coming my way.

    Thanks
    Al.
    AlBur
    Always Remember "Utopia Does NOT Exist"

  14. #14
    Join Date
    Apr 2017
    Location
    ROYSTON Herts
    Posts
    229
    Quote Originally Posted by AlBur View Post
    Fitted a new probe O-ring. No better.
    Worse still when I tried to fill it up it began leaking air at around 150 Barg. Appears to be coming from a point where barrel meets the action. Loses pressure quite quickly.

    Thought I would take it to Customguns at Hartlepool. However it would appear that he stopped accepting work in September. Showing "permanently closed" on internet.

    Anyone any further thoughts or is it a hefty bill coming my way.

    Thanks
    Al.
    Try filling with the probe locked forward

  15. #15
    Join Date
    Oct 2017
    Location
    Briston
    Posts
    106
    sounds like your harper valve seal may be knackered, the harper valve is a doddle to work on as its an open design, if seal was inconsistent that may also explain the scattering of shots, did you check the Map to find a premier partner near you?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •