Lincoln Jeffries / BSA 1906 Bayonet Under Lever Rifle

[piggy589]

I read an article recently where the author said that a well meaning owner could bring about the premature demise of a stock.

Lubricating the action and standing the gun upright, allowing the mix to soak into the timber.

[Huttles94]

According to the John Knibbs book, the sixth batch BSA's first came out in Feb/March 1907.

And by action tube do you mean top of the cylinder? Im sure they were stamped H the Lincoln and not Lincoln Jeffries Mod.H

If you could provide the serial number it would make things a lot clearer.

A bit odd but you could have a early batch Lincoln jeffries which has had another stock put on at a later date, or it could be a BSA made H the lincoln (but I believe only the early models made by BSA were stamped H the lincoln or Lincoln jeffries pattern).

Or I could just be getting things muddled up. Like I said a serial number will tell us exactly what it is (at least what the trigger block is off. if it is a bitsa)

But still, dont think I have ever seen one stamped Lincoln Jeffries Mod.H so I am a bit confused but very intrigued.

[Gareth W-B]

According to the John Knibbs book, the sixth batch BSA's first came out in Feb/March 1907.

And by action tube do you mean top of the cylinder? Im sure they were stamped H the Lincoln and not Lincoln Jeffries Mod.H

If you could provide the serial number it would make things a lot clearer.

A bit odd but you could have a early batch Lincoln jeffries which has had another stock put on at a later date, or it could be a BSA made H the lincoln (but I believe only the early models made by BSA were stamped H the lincoln or Lincoln jeffries pattern).

Or I could just be getting things muddled up. Like I said a serial number will tell us exactly what it is (at least what the trigger block is off. if it is a bitsa)

But still, dont think I have ever seen one stamped Lincoln Jeffries Mod.H so I am a bit confused but very intrigued.

Hi. Yes I mean the stamping on the cylinder, and word for word the stamping actually says:

H THE "LINCOLN" AIR RIFLE. PATENT 8761/04.

The serial number on the trigger block is: 14937. Many thanks.

[Huttles94]

Hi. Yes I mean the stamping on the cylinder, and word for word the stamping actually says:

H THE "LINCOLN" AIR RIFLE. PATENT 8761/04.

The serial number on the trigger block is: 14937. Many thanks.

Yes it is a 6th batch BSA.

Right I personally think it might be a bitsa. My reason for doing so is that the early BSA rifles would have had "THE BSA AIR RIFLE (LINCOLN JEFFRIES PATTERN) stamped on the cylinder. But that is only on the first few batches of BSA rifles (they dropped the "LINCOLN JEFFRIES PATTERN" in 1906 and just had "THE BSA AIR RIFLE" or "BSA AIR RIFLE).

So it looks like a cylinder and barrel off a Lincoln but a trigger block and stock off a BSA. I dont think it would have left the factory like that since the two parts were made in separate places (LJ was still making them in his workshop at this time). I have found in some Bitsa I have owned that if you are lucky you can get some parts that fit together and make a bloody decent rifle. That is what I think this is. Though like someone else has said, check to see if there is a serial number under the barrel (it will be hidden by the lever) Though I have only seen the later ones (Standards and CS models) have their serial numbers stamped in this place.


Im sure someone with more knowledge on here will help the truth come to light!

[Gareth W-B]

.
Thanks ​Huttles94. Appreciated.

[Gareth W-B]

Though like someone else has said, check to see if there is a serial number under the barrel (it will be hidden by the lever) Though I have only seen the later ones (Standards and CS models) have their serial numbers stamped in this place.

Cheers again. On the underside of the barrel down near the cocking lever pivot point is the number 49. Any significance?

[Josie & John]

Cheers again. On the underside of the barrel down near the cocking lever pivot point is the number 49. Any significance?

Hi Gareth,

If you remove the tap cover, the tap should be stamped with the same number.

I would have expected the rifle to have a Lincoln stamped stock if it were a Lincoln, so chances are a previous owner may have swapped parts around to make up a working gun. You just need to look on t'bay to see these old classics being parted out on a regular basis.

John

[Gareth W-B]

.
Cheers John, but no cover on the left side of the tap to remove, as it has a knurled round wheel instead, and am loathed to remove this to check ...

With a BSA number on the trigger sction however, it is more than just the stock that would need exchanging to make it a pure representation of a marque, however, so the way I see it, I have five options:

1) Obtain and fit a BSA cylinder tube so that everything is all BSA;
2) Obtain and fit an LJ stamped trigger action and stock so that all is LJ;
3) Keep and leave as is, as has obviously been this way for the better part of the last 100 years;
4) Sell as is — ensuring the buyer knew it was an artisan hybrid gun, or ...
5) Break it for its component parts and sell off all as spares to renovators?

Thoughts please.

[ptdunk]

Hi Gareth,

There should be a serial number on the inside of the cocking arm that is supposed to match the serial number on the trigger block.
Have a look if you can find one, and see if they match....sometimes the cocking arm doesn't have one though.

I'd be suprised if the H.Model cylinder and BSA trigger block were factory assembled, as technically they are two different brands, albeit both manufactured by BSA.
It's definately possible though.

Not sure if the cylinder and trigger block were screwed together first, then drilled for the trigger bolts. That would mean they probably were not interchangable.

Hope someone can shed some light on it for you.

Cheers,
Matt.

[Gareth W-B]

Hi Gareth,

There should be a serial number on the inside of the cocking arm that is supposed to match the serial number on the trigger block.
Have a look if you can find one, and see if they match....sometimes the cocking arm doesn't have one though.

I'd be suprised if the H.Model cylinder and BSA trigger block were factory assembled, as technically they are two different brands, albeit both manufactured by BSA.
It's definately possible though.

Not sure if the cylinder and trigger block were screwed together first, then drilled for the trigger bolts. That would mean they probably were not interchangable.

Hope someone can shed some light on it for you.

Cheers,
Matt.

Thanks for the indicator, Matt, I will have a good look on the under side of the under lever for a number in the daylight of tomorrow morning.

[Gareth W-B]

I read an article recently where the author said that a well meaning owner could bring about the premature demise of a stock.

Lubricating the action and standing the gun upright, allowing the mix to soak into the timber.

Yes, I have heard of that, so thanks for the considered thought, as you may very well be on the money.