nice mate... 1mm wall is fine for a man with your maching accuracy, and I guess the stroke stays "as is" ?
A friend at my local club recently asked me to do a tune on his 95 he only shoot's standing and as such likes the lightweight of the 95 , it's a keeper and he requested " as good as I could get it ", So a challenge . I have done a few Hw 80's with a 24 mm reduced cylinder tune , this last year , so a measure up, a deep breath , and I managed to massage the tune a bit to make it fit and bobs your uncle , a lightweight low recoil easy to cock break barrel, It's turned out rather nice , would make a superb hunting tool.
I think this might be a first for the 95 .
https://photos.app.goo.gl/JYC6Nvk2W33RxwBB9
nice mate... 1mm wall is fine for a man with your maching accuracy, and I guess the stroke stays "as is" ?
Always looking for any cheap, interesting, knackered "project" guns. Thanks, JB.
Pretty much John it lends itself well to the 24 mm treatment , tried machining a 25 mm hw seal down but had no luck, can't guarantee a size , so went o ring again, it's got a tad more stroke than the 80 so a little softer cycle, nice tune all round.
Could probably push to 23 mm with a bespoke piston, but as I found bin my 80 can get a bit fast ,and that's not to everyone's taste
Last edited by NickG; 28-09-2021 at 02:44 PM.
Can you delay delivering it until after the bash?
Tremendous work mate.
Put on heading 270, assume attack formation
Superb stuff, Nick; sounds most excellent..
Will you be doing one of your own now then?
Imagine this with the 98 stock fitted.
What spring did you opt for?
THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
NEXT EVENT :- May 4/5, 2024.........BOING!!
Just asked the owner if I can bring it to the bash awaiting a reply , fingers crossed
It's a yes 👍
Excellent news, Nick; thank you..
Would love to have a go, pretty please!
THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
NEXT EVENT :- May 4/5, 2024.........BOING!!
Absolutely, anyone is welcome to try my toys, and my friends, of course !, I also have a development of my 21 tx to bring if it works that is 😂
Of course it will work, Nick. And beautifully.
THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
NEXT EVENT :- May 4/5, 2024.........BOING!!
Excellent; will look forward to the updates, sir. Best of luck.
THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
NEXT EVENT :- May 4/5, 2024.........BOING!!
anti bounce is defo an area to research. it just has to hold/delay the bounce, as the airflow is so great, even a 1ms delay will have a big effect on power output/bounce reduction.
I've sketched a TP one way valve arrangement out a few times, but it's (too) tricky to make
Always looking for any cheap, interesting, knackered "project" guns. Thanks, JB.
I have two prototypes , posh word for lash up 😉, one is a hollow head "dead blow" hammer style , with either a spring loaded weight or lead shot, that's not been vin a gun yet. The second is based on a meteor piston head design , and uses the theory that that a lip seal expands at the bounce point causing a braking effect, this one appears to
Work , details a bit long for this post , will put some pics on .