I'm looking for used 12g 70mm cartridges please. Preferably all the same type. Willing to pay reasonable price and postage.
Many thanks
Daystate Air Ranger FAC - Kral Bullpup & NP03 - CZ 452 .22lr - Lithgow 17hmr - Remington 783 .223 - Franchi 612vs 12G - Renato Gamba 12G O/U - Hatsan Escort 12G
Nostalgia isn't what it used to be.....
Sheesh.....It's never simple is it
I Guess by sticking to well known makes I'll be OK? i.e. Hull, gamebore, lyalvale etc
Daystate Air Ranger FAC - Kral Bullpup & NP03 - CZ 452 .22lr - Lithgow 17hmr - Remington 783 .223 - Franchi 612vs 12G - Renato Gamba 12G O/U - Hatsan Escort 12G
Nostalgia isn't what it used to be.....
If you don't mind paper cases Kranks do them by the 100 ready primed.
They can be reloaded a few times until the crimp mouth goes soft. The thing to watch for with paper cases
is small black burn marks like pinholes where the case meets the head.
If you see them scrap the case as it is on the verge of separating.
You could try clay shoots to find suitable cases,they usually have a problem disposing of them.
I know one shoot that has two jumbo bags spilling over with fired cases.
The easy option is to trim the star crimp off them and use a card and rolled turnover crimp. I load all my bp cartridges that way. The turnover tool fits in my pillar drill.
[I]DesG
Domani e troppo tardi
My intention was to buy new primed cases then re-use them. The guy at FES who I intend to get the kit from said the Lee Load-All II is not very good when it comes to crimping new cases and I was better off with used cases.
Daystate Air Ranger FAC - Kral Bullpup & NP03 - CZ 452 .22lr - Lithgow 17hmr - Remington 783 .223 - Franchi 612vs 12G - Renato Gamba 12G O/U - Hatsan Escort 12G
Nostalgia isn't what it used to be.....
Go to a clay shooting ground and collect as many as you can carry for free.
If you want used 12G cases then:
1. Choose a brand that has reloading data published for them!
2. Do not mix case types.!
3. You cannot "work up a load for them" as pressures do NOT show up like rifle cases.
4. If you find a suitable PUBLISHED load then stick to it! For example changing primer type may cause adverse changes in pressure.
5. Is your gun proofed for such loads? How was your proof derived?
6. Do not be deceived into thinking "fast" loads will be of benefit; lead shot has the ballistic qualities of a heavy ping pong ball! E.g. if you don't believe this then
consider the extreme range of lead shot!
7. Some published factory data is "enthusiastic" to say the least.
8. All my reload data has been put through a pressure gun (piezo) and stacks up with my chrono data. No, I will not detail this as it suits my gun , choke and
pattern requirements. But I can tell what to look for.
9. Stay away from the higher pressure loads!!!!!!!!!!!!
10. And finally I still have about 10000 once fired Winchester AA 70mm cases; in my opinion the best for reloading (scarce as hens teeth now) and have just
finished reloading 4500 shells (32 gram @ 1250 f/s). Yes, I have seen factory ammo rated at high velocity but have you ever fired a one ounce load at 1500+
f/s (over the chrono?).
11. And finally please don't "screw around" altering cases (changing crimp to roll) UNLESS YOU HAVE THE PRESSURE DATA!
Cheers
pjinoz
I've not long dumped a heap of spent 12g carts, mainly eley olympic blue.
I'll take better care of the next load I generate, likely to be a mix of fiocchi TT1's (67mm, that work well in my 3" chambered 525) and Eley Olympic Blue (70mm).
I've never re-loaded 12g, but I've been reloading .410 this last while and whilst these 12g carts aren't fancy high brass cases, IMO they'd take a reload especially if reforming the crimp on a press, but then I'm unsure of the type of original crimp on the TT1, because I don't have any left to check, the blues are a 6.
So if those are any good to you, let me know and I'll save what I can.
If you can get to East Herts before the recycle man we have half a dozen tonne bags full, loads of makes, sizes and bore. Take your pick.
Good deals with: Muskett, Dreben, roger.kerry, TALL, Helidave1, Chelseablue, Leeroy7031, Mousemann, pnuk, Practical, NEWFI, HOOGS, Webb22, lazybones1416 and deanw5262 among others. Thanks Guys.
Thanks guys
Yesterday as it happens I picked up about 400 used carts from a very helpful guy at Gatwick Clay School. Mostly Eley 1st 67mm but a good 100 or so 70mm Lyalvale English Sporter 70mm which I think are the ones I'll use.
I know the Eley 1st are a cheap cartridge. Does that mean they are less suitable for reloading?
As for load, I found a place called Folkestone Engineering Supplies who supply all the stuff I need and also give suggested loads. I'll be looking at the fibre wad, 34g No6. They suggest:
70mm Case
1.7g Maxan CSB3
4mm card
16mm Fibre Wad
34g #6 shot
Star Crimp
I guess if I go for the shorter 67mm carts I'll have to reduce the shot and powder?
Daystate Air Ranger FAC - Kral Bullpup & NP03 - CZ 452 .22lr - Lithgow 17hmr - Remington 783 .223 - Franchi 612vs 12G - Renato Gamba 12G O/U - Hatsan Escort 12G
Nostalgia isn't what it used to be.....
The fellow at FE, is a well respected figure known for his expertise and willingness to help. He's best placed to advise you on components for his loads, cart wise. I live at the polar opposite end of the country, yet even I have spoken to the fellow a few times, and bought a few bits and bobs from him.
From what I've gleaned, if a spent cart passes inspection then it should be good to go. Some carts are better than others in terms of reuse and from general observation I've concluded that, at least for 28g loads, 12g carts survive the initial firing much better than .410 How many subsequent reuses you'll get will depend on the cart quality and load.
The load will be the same for the shorter 67mm cartridges, but it might not fit. So some experimentation maybe required to get a handle on the wad makeup etc. to have the 70mm load fit into a shorter cart. But the carts are basically the same thing be they 65 67 70 76 etc. it's just the capacity that alters, there are a couple of different cart types, at least in .410, that require specific data, most european carts are the same type, parallel wall.
Obviously if you alter the shot load wad type you alter the powder accordingly.