Page 7 of 9 FirstFirst ... 56789 LastLast
Results 91 to 105 of 126

Thread: A 'How to' guide to sharpening a knife the traditional way.

  1. #91
    Join Date
    Jul 2012
    Location
    Newcastle
    Posts
    9
    That's the method I always use, being a joiner myself, I was taught well on the uses of an oil stone, a blunt knife, chisel, plane etc is useless, look after your tools, no matter what there value is,
    I must say I struggle on the curve of the tip !

  2. #92
    Join Date
    Feb 2009
    Location
    wigan (the frozen north)
    Posts
    227

  3. #93
    Join Date
    Feb 2009
    Location
    wigan (the frozen north)
    Posts
    227
    Last edited by mule77; 02-09-2012 at 08:38 PM. Reason: Double post

  4. #94
    Join Date
    Sep 2012
    Location
    Glasgow
    Posts
    2
    Quote Originally Posted by snock View Post
    By 'traditional' I mean by using an oilstone or waterstone. The waterstones are available online from outlets like these or you might have a shop on your local High Street which does them or the oilstone.

    Whichever you decide to buy, there are differences in using them, but for the benefit of confusion, I shall assume that you have bought the oilstone, as that's what many of you will find more readily available.

    A very sharp knife is a microscopically fine saw, the act of sharpening simply re-sets the teeth of that saw.

    OK, we've got an oilstone, some light oil [3-in-1 is fine], some rags, a leather belt and some plasters.

    First off, we assess which side of the stone to use; rough or fine, by determining how blunt the blade is.
    The stone should be placed flat on a clean surface [the inside of the wooden box it comes in perfect] and shouldn't be able to move around on the bench.
    We then need to apply just a few drops of oil onto the stone and smooth this onto the stone's surface with a spare finger.

    Presuming we only need to re-touch the edge with the fine side of the stone, we need to place the blade onto the stone at an angle of around 20 degrees and make steady, even strokes with light pressure edge first from the edge nearest the finger guard[choil] to the tip of the blade [guide to blade geometry]. The handle will need to be raised slightly as to keep the tip on the stone due to the changing geometry of the blade/stone interface.

    Start by doing between 5 and 10 sweeps of the blade from choil to tip on one side away from you, wipe off the oil then turn the knife over and do the same amount of sweeps toward yourself. Stop here and feel the edge with your thumb tip for burrs on either side of the edge; if there are none, carry on with the sweeps. If there is a burr, don't worry..this is what you want.

    Once we have a burr on one edge we need to imagine what our blade looks like from a tip-on perspective. A burr will make the blade look like a ' y ', rather than a 'v'. We just need to straighten this burr out.

    Taking note of which side of the blade has the burr on, that is the side we need to concentrate on. Repeat the sweeps, but this time use very light pressure on the blade and check all along the edge for the burr after each sweep. Once the burr has gone, check the other edge for a burr. The burr, if you've used too much pressure on the blade at this last stage has been too much, will have transferred to the other side of the edge; just 'move' the burr so that its hardly detectable on any side. The stone work has finished.

    All that's needed now is to give the edge a strop on a leather belt. This will polish the re-set saw teeth for a more durable edge.

    Attach one end of the belt to something like a vice or hook so that you can get some tension on it.
    Once you've done this you need to hold the other end in your left hand [right hand if left-handed], and make slow, even draws on the blade working spine [blunt side] toward yourself. After each stroke, turn the blade over and push it away from you whilst applying the same light, even pressure you used on the previous stroke. Continue for multiples of 5 or 10 on each side, just for consistency.

    Once you've done all this, and you've got yourself a very keen edge, you'll begin to see the skills develop which will stay with you for life, and you'll feel better for learning how it's done.

    Try the blade on a sheet of paper; it should cut with pressure alone.
    Hi guys

    is it better to use old methods or new gismos to sharpen knives. there are also different grades of sharpenning stones.

  5. #95
    Join Date
    Jun 2012
    Location
    Worcester
    Posts
    39
    http://www.youtube.com/watch?v=KW64B0MZVOE

    I have one of these kits and they are excellent.

  6. #96
    Join Date
    Feb 2009
    Location
    wigan (the frozen north)
    Posts
    227
    Quote Originally Posted by diipii View Post
    http://www.youtube.com/watch?v=KW64B0MZVOE

    I have one of these kits and they are excellent.
    That looks a bit dangerous to me pushing the stone towards the sharp edge. One slip and the bloods flowing

  7. #97
    Join Date
    Apr 2010
    Location
    Middlesbrough, England
    Posts
    64
    Hi Guys Im an ex butcher and its fascinating to see so many fellas getting 'horned up ' over knives.
    Always found a 'steel' to be the best for me (FDick multi cut) but it does need regular usage to retain an edge, i only reverted to an oilstone once/twice a year if things got really blunt
    Pete

  8. #98
    Join Date
    Feb 2009
    Location
    wigan (the frozen north)
    Posts
    227
    Personally I really enjoy the whole waterstone and stroping process I can spend hours sharpening my knives, axes and parang

  9. #99
    Join Date
    Jan 2013
    Location
    Northampton
    Posts
    5

    Great post

    Excellent post !!!

  10. #100
    Join Date
    Mar 2013
    Location
    cheltenham
    Posts
    22
    Great stuff and informative. Cheers

  11. #101
    Join Date
    Apr 2012
    Location
    Hemel Hempstead
    Posts
    188
    Quote Originally Posted by skinhead View Post
    Gentlemen, a question. When using an old belt for stropping, is it best to use the burnished front of the belt or the sueded back of the belt? I've always assumed the back, but stand to be corrected.

    Si
    use the sueded back as it acts as a wick/resevoir for your stropping paste. autosol or starkie blue will give good results. if you can glue the belt to a flat bit of wood it will give better results.

  12. #102
    Join Date
    Apr 2012
    Location
    Hemel Hempstead
    Posts
    188
    Quote Originally Posted by Fat Pep View Post
    Hi Guys Im an ex butcher and its fascinating to see so many fellas getting 'horned up ' over knives.
    Always found a 'steel' to be the best for me (FDick multi cut) but it does need regular usage to retain an edge, i only reverted to an oilstone once/twice a year if things got really blunt
    Pete
    generally a steel only realignes the edge of the blade, correcting any rolls of the edge etc. it does not actually sharpen.

  13. #103
    Join Date
    Apr 2012
    Location
    Hemel Hempstead
    Posts
    188
    Quote Originally Posted by mule77 View Post
    or, Longstrider, the man who can sharpen a knife so that it will slice through a standing rizla


  14. #104
    Join Date
    Aug 2013
    Location
    south shields
    Posts
    161

    knife sharpening

    good thread, will give this a try on my buck alpha hunter as its getting a little bit dull and was paranoid about messing the edge up when sharpening, but sounds pretty straight forward, fingers crossed.

  15. #105
    Join Date
    Jul 2013
    Location
    falkirk
    Posts
    225
    Just put this to good use myself, all the knives in the kitchen are better than they were new.
    I STILL MISS MY EX
    But My Aim IS Getting Better!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •