Page 1 of 4 123 ... LastLast
Results 1 to 15 of 50

Thread: walther lgu - spring maybe goosed.

  1. #1
    Join Date
    Mar 2011
    Location
    Wakefield
    Posts
    192

    walther lgu - spring maybe goosed.

    My lgu is struggling , I think the spring may be fatigued even though it's not done that much .

    Checked the breach seal which appears good and the piston seal is ok.

    Anybody got any thoughts or info on the subject.

  2. #2
    Join Date
    Apr 2012
    Location
    Retford, Notts
    Posts
    37,287
    There have been threads on this very subject in the past and in Jim's excellent article recently in Airgun World.

    The word on the street is that the transfer port diameter is too small, leading to excessive choking and the resulting piston bounce wearing the spring prematurely.

    The port needs opening out a tad.

    Can't remember the recommended diameter, but it'll be on those threads and in Jim's article.
    THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
    NEXT EVENT :- May 17/18, 2025.........BOING!!

  3. #3
    Join Date
    Mar 2011
    Location
    Wakefield
    Posts
    192
    The tp is 2.6mm ish in standard trim , a mate reamed mine out to 3.3 ish.

  4. #4
    Join Date
    Apr 2012
    Location
    Retford, Notts
    Posts
    37,287
    Has it lost power SINCE the rebuild and TP diameter increase?

    Could be one of the seals, then; certainly worth double-checking.

    I think the spring on the Walthers is meant to be very good quality, so maybe not the first, automatic port of call, but anyone's allowed a duffer from time to time?
    THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
    NEXT EVENT :- May 17/18, 2025.........BOING!!

  5. #5
    Join Date
    Mar 2011
    Location
    Wakefield
    Posts
    192
    I guess it must be a couple of years old now , had the tp done within a couple of tins of pellets from new.

    It's always been struggling from day one.

  6. #6
    Barryg's Avatar
    Barryg is offline Registered ̶D̶i̶a̶n̶a̶ User
    Join Date
    Jan 2009
    Location
    Nr. YEOVIL
    Posts
    5,156
    Quote Originally Posted by seagate View Post
    My lgu is struggling , I think the spring may be fatigued even though it's not done that much .

    Checked the breach seal which appears good and the piston seal is ok.

    Anybody got any thoughts or info on the subject.
    Are you getting consistent fps?
    Also have you measured the cocking effort so you can compare it to the correct cocking effort.

  7. #7
    Join Date
    Mar 2011
    Location
    Wakefield
    Posts
    192
    It's always been consistent , in fact very consistent.

    The cocking effort - it never crossed my mind to think about that, so I've never measured it.I'm a dunce.

  8. #8
    Barryg's Avatar
    Barryg is offline Registered ̶D̶i̶a̶n̶a̶ User
    Join Date
    Jan 2009
    Location
    Nr. YEOVIL
    Posts
    5,156
    Quote Originally Posted by seagate View Post
    It's always been consistent , in fact very consistent.

    The cocking effort - it never crossed my mind to think about that, so I've never measured it.I'm a dunce.
    If you are getting consistent fps I would think it unlikely to be the seals
    I have found measuring the cocking effort a fair indicator of the spring and general health of a springer

  9. #9
    Join Date
    Mar 2011
    Location
    Wakefield
    Posts
    192
    Sounds logical.
    Thanks for your input gentlemen.

  10. #10
    Join Date
    Dec 2003
    Location
    Cambridge UK
    Posts
    7,147
    I bought a s/h LGU that was running c. 10.6. I had reason to believe it had been back to Armex because of low power. TP was 2.6. I opened it out to 3.2mm and with a small preload washer it went to c. 11.5, if I remember right. I then left the rifle untouched for about 2 months (uncocked before you ask) and power had dropped to about 10.5. I had bought a new kit from Germany so fitted the new spring. Output immediately regained 11.5. Rechecked two months later ... still 11.5.
    I came to the conclusion that there were some duff Walther springs around.
    Cheers, Phil

  11. #11
    Join Date
    Mar 2011
    Location
    Wakefield
    Posts
    192
    My local rfd is stumped for getting spares for my lgu.

    How do you go about sourcing spares from Germany, is it straight forward?

  12. #12
    Join Date
    Dec 2003
    Location
    Cambridge UK
    Posts
    7,147
    LGU spares sourced from Shneider, http://www.sportwaffen-schneider.de/ Ordering is simple but you have to open an account and provide some evidence of age. I believe I supplied a copy of a passport page. Web page appears in German but you can opt for an English translation. They have a broad range of spares for the LGU including a complete kit of mainspring, piston and spring guide. You can also get the mainspring on its own but remember to get the export spring or you will end up with a German power level.
    Cheers, Phil

  13. #13
    Join Date
    Mar 2011
    Location
    Wakefield
    Posts
    192
    I think I'm going to get piston,guide and spring.

    Thankyou .
    atb nick

  14. #14
    Join Date
    Apr 2002
    Location
    Near Wimbledon, SW London, or Lusaka, Zambia
    Posts
    26,987
    Quote Originally Posted by seagate View Post
    I think I'm going to get piston,guide and spring.

    Thankyou .
    atb nick
    I'd save your money and just get the spring.
    Always looking for any cheap, interesting, knackered "project" guns. Thanks, JB.

  15. #15
    Join Date
    Apr 2012
    Location
    Retford, Notts
    Posts
    37,287
    Can Solware not supply the parts?

    Maybe worth a try (as I seem to remember that they're a "Premier" Armex / Umarex Dealer)???
    THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
    NEXT EVENT :- May 17/18, 2025.........BOING!!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •