Page 2 of 2 FirstFirst 12
Results 16 to 27 of 27

Thread: Neck Turning - Donut Removal

  1. #16
    Join Date
    Apr 2001
    Location
    Chelmsford
    Posts
    6,406
    Quote Originally Posted by Elliott View Post
    Mmm.. Maybe eh. Probably half a dozen maybe.
    That's quite a bit of trimming, any signs of bright rings up near the case head. Id be looking at new brass myself as a simple fix.
    "Shooters, regardless of their preferred quarry, enjoy their sport for its ability to transfer them from their day-to-day life into a world where they can lose themselves for a few hours". B Potts.

  2. #17
    Parabuteo is offline My Chrony has bought it a couple of times...
    Join Date
    Mar 2006
    Location
    Southampton
    Posts
    6,061
    You need a neck reamer then and not a neck turner. Why take brass off the outside of the neck when it is forming at the shoulder/neck junction? The doughnut will still be there.

    Usually you only need to neck turn for a tight neck in the chamber or possibly to lightly true up the necks on some cases, but if it is all down to flow, it will just re-occur anyway as the brass flows forward into the neck. The errors in concentricity start back in the case body where one side might be thicker than the other and this simply extrudes forwards, so it will re-occur evetually if you just neck turn.

    If you are worried about incipient head seperation use a piece of wire with a bend and run it over the inside of the case, you will feel it before you see it by which time its replacement time.

    I have had 2 cases of head sep.

    In .303 where I FL re-sized. Neck only prevented it and I assume the chamber dims were a bit generous as the head spacing was ok

    In 5.56x45 where I swapped FL dies and did not set the new one up properly and over bumped the shoulders back. A Dillon gaugue soon showed the error and it was sorted.
    I'm a maggot in another life you know

  3. #18
    Join Date
    Nov 2010
    Location
    Lancaster
    Posts
    2,248
    Quote Originally Posted by Parabuteo View Post
    You need a neck reamer then and not a neck turner. Why take brass off the outside of the neck when it is forming at the shoulder/neck junction? The doughnut will still be there.
    Yes, that sounds like what I need. Where would I get one?

    .22LR CZ452; .22 Hornet CZ527
    Tikka T3 Varmint .223; .204 Ruger CZ527 Varmint;
    6.5 Creed Bergara B14 HMR

  4. #19
    Parabuteo is offline My Chrony has bought it a couple of times...
    Join Date
    Mar 2006
    Location
    Southampton
    Posts
    6,061
    Quote Originally Posted by Elliott View Post
    Yes, that sounds like what I need. Where would I get one?
    Forster make them. Try Hannams.

    Honestly though very few people ever suffer from it and you dont see many people messing with neck turning etc outside of wildcats and Benchrest/F.

    Are you neck sizing only, and if so are you going right back to the shoulder junction?
    I'm a maggot in another life you know

  5. #20
    Join Date
    Apr 2001
    Location
    Wet Cold Downtown Leicester
    Posts
    18,523
    You really shouldn't have this issue.

    How hot are your loads?

    All that brass comes from somewhere, I would double check everything you're doing before something seperates.
    A man can always use more alcohol, tobacco and firearms.

  6. #21
    Join Date
    Nov 2010
    Location
    Lancaster
    Posts
    2,248
    Quote Originally Posted by RichardH View Post
    You really shouldn't have this issue.

    How hot are your loads?

    All that brass comes from somewhere, I would double check everything you're doing before something seperates.
    Within book max, so not too hot.

    I'm a pretty competent reloader, I just want to extract that bit more accuracy and I figured neck turning/reaming could improve things for me.

    .22LR CZ452; .22 Hornet CZ527
    Tikka T3 Varmint .223; .204 Ruger CZ527 Varmint;
    6.5 Creed Bergara B14 HMR

  7. #22
    Join Date
    Jan 2008
    Location
    Daventry. Northants.
    Posts
    3,534
    Neck turning will give you more consistent neck tension only if you use bushing dies, using bushing dies without neck turning defeats the object of bushing dies because of variations in neck wall thickness, with unturned cases standard dies with a sizing button will give more consistent neck tension then bushing dies. If you get a donut form, KM neck turner mandrels are available with a built in donut cutter. Neck reaming will not remove case neck thickness variations, it is really only used when necking down cases to smaller calibres and then combined with neck turning

    TB.

  8. #23
    Join Date
    May 2012
    Location
    bridgend
    Posts
    7
    I have to neck turn brass for my 20ppc although it was meant to be a no turn neck. You need to be careful neck turning unless you have a tight chamber as if you take too much off and your reloading dies are normal size you won't get the neck tension. I know from experience as I've ruined a few pieces of brass.

  9. #24
    Parabuteo is offline My Chrony has bought it a couple of times...
    Join Date
    Mar 2006
    Location
    Southampton
    Posts
    6,061
    Quote Originally Posted by RichardH View Post
    You really shouldn't have this issue.

    How hot are your loads?

    All that brass comes from somewhere, I would double check everything you're doing before something seperates.
    Fair comment.

    I did not check the shoulder bump on my 5.56 NATO loads after changing over to another die and ended up with a separated case in a comp. I have had the rifle re barelled since and it has a different chamber profile (to allow for hot service ammo to extract easilly) which works well but again I have to reduce my bumping back/FL die setting.
    I'm a maggot in another life you know

  10. #25
    Join Date
    Dec 2007
    Location
    huddersfield
    Posts
    551

    neck turning

    Quote Originally Posted by Elliott View Post
    Yes, that sounds like what I need. Where would I get one?
    I have some k an M neck turning and neck reaming in a box somewhere
    Message me tomorrow when I have time to root it out.
    John F.

  11. #26
    Join Date
    Dec 2007
    Location
    huddersfield
    Posts
    551
    Quote Originally Posted by himself View Post
    I have some k an M neck turning and neck reaming in a box somewhere
    Message me tomorrow when I have time to root it out.
    John F.
    Have found the above mentioned items,they are for 6mm cases.
    John F.

  12. #27
    Parabuteo is offline My Chrony has bought it a couple of times...
    Join Date
    Mar 2006
    Location
    Southampton
    Posts
    6,061
    Why specifically would you find a dougnut in a cartridge and not say...a sausage roll? This demonstrates wonton lack of pastry control IMHO
    I'm a maggot in another life you know

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •