Page 1 of 2 12 LastLast
Results 1 to 15 of 19

Thread: Pig in a poke Pt2 The internals. Information please.

  1. #1
    Join Date
    Jun 2012
    Location
    North Wales
    Posts
    3,275

    Pig in a poke Pt2 The internals. Information please.

    Got the 55 in bits yesterday. Serial 80639 suggests 1960 so a lot younger than me and in similar nick.
    Queries are i) should it be leather seal ii) is the piston modified iii) were all trigger blocks threaded for guide iv) will any other cocking arm fit ?
    TP is 4.5 mm, bore 25 mm stroke 71 mm so should make power OK but may need TP throttling a bit if synthetic seal retained??




    Thanks for looking.

  2. #2
    Join Date
    May 2008
    Location
    Quigley Hollow, Nuneaton
    Posts
    17,125
    Hi Jules.

    The piston seal originally would have been leather --- your piston looks to have an adaptor on it.

    As far as I'm aware you have the correct guide but your back block has been altered for a retained guide.

    The cocking arm is the same as an early HW35 --- later 35 cocking arms have an anti click bulge in them.



    All the best Mick

  3. #3
    Join Date
    Mar 2006
    Location
    Worcester
    Posts
    22,222
    I agree with Mick, though the piston looks identical to the one in my HW50. My HW55 has a very different piston, with two slots, and a large aluminium head that protrudes back into the piston and restricts spring room.

    I'd neck down the hole that's been drilled in the trigger block, or make a spring guide to fit in it.

  4. #4
    Join Date
    Mar 2006
    Location
    Worcester
    Posts
    22,222
    Top HW55 piston aluminium block arrowed.
    Below HW50 piston

    P1040307.jpg

  5. #5
    Join Date
    Nov 2009
    Location
    Monmouth, Land of Wales.
    Posts
    14,441
    Personally, I'd be going with a new spring (yours looks kinky!).

    Plastic TH, and steel spring guide fixed in the trigger block (seeing as somebody's already done the work machining it).

    And sleeve down the TP to 3.2ish?... 4.5mm sounds a bit huge, doesn't it?



    (I don't recognise the seals on those pistons of yours, Jim?)

  6. #6
    Join Date
    May 2008
    Location
    Quigley Hollow, Nuneaton
    Posts
    17,125
    Quote Originally Posted by Rickenbacker View Post

    And sleeve down the TP to 3.2ish?... 4.5mm sounds a bit huge, doesn't it?
    I'd be starting a bit smaller at 2.5mm, Phil --- then you can drill it out bigger if needed.

  7. #7
    Join Date
    Nov 2009
    Location
    Monmouth, Land of Wales.
    Posts
    14,441
    Quote Originally Posted by T 20 View Post
    I'd be starting a bit smaller at 2.5mm, Phil --- then you can drill it out bigger if needed.
    Ah, interestingly small to start off with, Mick.

  8. #8
    Join Date
    Mar 2006
    Location
    Worcester
    Posts
    22,222
    Quote Originally Posted by Rickenbacker View Post
    (I don't recognise the seals on those pistons of yours, Jim?)
    You won't Phil. Just a couple of thin PTFE temporary seals to see how the rifles shot with 70mm stroke.

  9. #9
    Join Date
    Jun 2012
    Location
    North Wales
    Posts
    3,275
    Many thanks for the support all. I have a much later 55T so may have a peek inside just for curiosity.
    On that note Jim what was the stroke before you went for 70 mm?

  10. #10
    Join Date
    Oct 2007
    Location
    Alkmaar The Netherlands
    Posts
    682
    The early HW55 models did have a fixed spring guide ..
    At a later date this feature was changed to the separate guide, not sure at what date that was done though?
    I would remove the piston seal adapter and replace it with a leather seal as it should be.

    .


    ----------------------------
    Frank

  11. #11
    Join Date
    Apr 2012
    Location
    Christchurch
    Posts
    4,916
    [QUOTE=Rickenbacker;7456650]Personally, I'd be going with a new spring (yours looks kinky!).

    Plastic TH, and steel spring guide fixed in the trigger block (seeing as somebody's already done the work machining it).

    And sleeve down the TP to 3.2ish?... 4.5mm sounds a bit huge, doesn't it?




    I agree, think 4.5 TP would be problematic.

    Baz
    BE AN INDEPENDENT THINKER, DON'T FOLLOW THE CROWD

  12. #12
    Join Date
    Mar 2006
    Location
    Worcester
    Posts
    22,222
    Quote Originally Posted by deejayuu View Post
    Many thanks for the support all. I have a much later 55T so may have a peek inside just for curiosity.
    On that note Jim what was the stroke before you went for 70 mm?
    From memory, 65mm. My HW55 does have the fixed rear spring guide, and I'm guessing the one originally in yours was probably deliberately removed because it wouldn't fit inside a beefier after market spring.

  13. #13
    Join Date
    Jun 2012
    Location
    North Wales
    Posts
    3,275
    Thanks again. Must get on with it! I'm suspicious about the trigger unit. Has wear consistent with age and pre safety frame with stop pin above main sear but
    the sear fouls the slot in main cylinder so has to be depressed to unscrew the block. Read somewhere that early 55T had match trigger later became Rekord for 35??
    Last edited by deejayuu; 13-03-2018 at 10:27 PM.

  14. #14
    Join Date
    Mar 2006
    Location
    Worcester
    Posts
    22,222
    Quote Originally Posted by deejayuu View Post
    ...the sear fouls the slot in main cylinder so has to be depressed to unscrew the block...
    I have to do the same with both my HW50 and HW55, Jules.

  15. #15
    Join Date
    Jun 2012
    Location
    North Wales
    Posts
    3,275
    Thanks again Jim probably correct to the action then.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •