Page 1 of 2 12 LastLast
Results 1 to 15 of 20

Thread: Softer HW99 Mainspring?

  1. #1
    Join Date
    Jan 2014
    Location
    leicester
    Posts
    140

    Softer HW99 Mainspring?

    My 0.177 HW99 has had the usual fettling including a Delrin top hat, spring guide and a PTFE piston sleeve. It currently has the standard HW mainspring without preload washers, and shoots JSB 8.5 gn. at 11.25 Ft.Lbs.

    I would like to trade some power for a smoother firing cycle, thinking that an alternative, softer mainspring would be a better solution than cutting a coil or so off the existing mainspring.

    Is fitting a softer mainspring the best approach, and if so could someone suggest an alternative mainspring?

    Thanks and Best Regards,
    Bill.

  2. #2
    Join Date
    Jul 2012
    Location
    Hemel hempstead
    Posts
    730
    Quote Originally Posted by billsnibby View Post
    My 0.177 HW99 has had the usual fettling including a Delrin top hat, spring guide and a PTFE piston sleeve. It currently has the standard HW mainspring without preload washers, and shoots JSB 8.5 gn. at 11.25 Ft.Lbs.

    I would like to trade some power for a smoother firing cycle, thinking that an alternative, softer mainspring would be a better solution than cutting a coil or so off the existing mainspring.

    Is fitting a softer mainspring the best approach, and if so could someone suggest an alternative mainspring?

    Thanks and Best Regards,
    Bill.
    I have a wonky donkey service kit in my 99s and that came with a longer spring in the kit

  3. #3
    tinbum's Avatar
    tinbum is offline Killer Vampire Lesbians on scooters
    Join Date
    Aug 2007
    Location
    Daarn Saaarf!
    Posts
    19,799
    The .177 will run much smoother at 10.5. Lose half a coil and try again, repeat if necessary.
    Better to admit you walked through the wrong door than spend your life in the wrong room

  4. #4
    Join Date
    Apr 2012
    Location
    Retford, Notts
    Posts
    37,287
    As the man says above, just shortening the existing spring slightly may well have the desired effect.

    I have a WonkyDonky kit in one of my 99s and it's lovely. You could approach him and see if he has a spring. I could well be tempted to ask him for a .22 spring, sacrificing power for the even milder cycle that you are after, although some would say that it may drop the power too low. Worth a try in my opinion and you could add a little preload if the output was too low.

    If you have the spring out of the gun at present, you could check its measurements against some of those stated on the Mainspring Data Thread in the Useful Tips section.

    If choosing a new spring, don't forget you'll need to make sure that the guide (and top hat if desired) fit properly.
    THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
    NEXT EVENT :- May 17/18, 2025.........BOING!!

  5. #5
    Join Date
    Jan 2014
    Location
    leicester
    Posts
    140
    Thanks all for the advice. A thought: would collapsing a coil have the smoothing effect on shooting characteristics I'm after?

    It seems that this would be the equivalent of shortening the spring and adding some preload washers, and wouldn't involve having to refinish the spring end. If it wasn't beneficial I could then remove the collapsed coil and refinish the end to achieve the shortened spring situation.

    Best Regards,
    Bill.

  6. #6
    tinbum's Avatar
    tinbum is offline Killer Vampire Lesbians on scooters
    Join Date
    Aug 2007
    Location
    Daarn Saaarf!
    Posts
    19,799
    Quote Originally Posted by billsnibby View Post
    Thanks all for the advice. A thought: would collapsing a coil have the smoothing effect on shooting characteristics I'm after?

    It seems that this would be the equivalent of shortening the spring and adding some preload washers, and wouldn't involve having to refinish the spring end. If it wasn't beneficial I could then remove the collapsed coil and refinish the end to achieve the shortened spring situation.

    Best Regards,
    Bill.
    It will work, but added dead preload often increases cocking effort and piston bounce for the same power.
    However, it is quick, easy and FREE!!
    Better to admit you walked through the wrong door than spend your life in the wrong room

  7. #7
    Join Date
    Apr 2002
    Location
    Near Wimbledon, SW London, or Lusaka, Zambia
    Posts
    26,987
    I run mine with a longer, softer spring. Nicer, softer firing cycle, easier cocking, and less piston bounce.. power is actually unchanged at just over 11 (in .177)
    Always looking for any cheap, interesting, knackered "project" guns. Thanks, JB.

  8. #8
    Join Date
    Dec 2003
    Location
    Cambridge UK
    Posts
    7,147
    Quote Originally Posted by Shed tuner View Post
    I run mine with a longer, softer spring. Nicer, softer firing cycle, easier cocking, and less piston bounce.. power is actually unchanged at just over 11 (in .177)
    Excellent, but do you know which rifle that spring was original equipt for?
    Cheers, Phil

  9. #9
    Join Date
    Aug 2001
    Location
    Swansea valley.
    Posts
    2,773
    I remember talking to Shauny about this and he finds a Titan meteor spring (cant remember the number), works well in these. Probably need a piston sleeve as likely be of smaller diameter.

  10. #10
    Join Date
    Apr 2002
    Location
    Near Wimbledon, SW London, or Lusaka, Zambia
    Posts
    26,987
    Quote Originally Posted by Phil Russell View Post
    Excellent, but do you know which rifle that spring was original equipt for?
    Cheers, Phil
    err, well.... it was the 4th one I found in the second drawer of my cantilever toolbox full of springs...
    Always looking for any cheap, interesting, knackered "project" guns. Thanks, JB.

  11. #11
    Join Date
    Aug 2001
    Location
    Swansea valley.
    Posts
    2,773
    Ah yes I know that spring

  12. #12
    Join Date
    Dec 2003
    Location
    Cambridge UK
    Posts
    7,147
    Quote Originally Posted by Shed tuner View Post
    err, well.... it was the 4th one I found in the second drawer of my cantilever toolbox full of springs...
    Now there is a man after my own heart ......
    Cheers, Phil

  13. #13
    Join Date
    Jul 2015
    Location
    Hastings
    Posts
    1,498
    Bill,

    I fitted a 0.22" Wonky Donky service kit into my 0.177" HW99S, and it made ca. 10.0 ft.lb, with no compression washers fitted.

    Lovely to shoot, and much easier to cock that when the rifle is at ca. 11 ft.lb.

    Compare the trajectories of 10 ft.lb, and 11.5 ft.lb in Chairgun, and you see you are losing virtually no trajectory with 10 ft.lb

    Have fun

    Best regards

    Russ

  14. #14
    Join Date
    Jul 2001
    Location
    East Chinnock
    Posts
    650
    Shortening a spring increases stiffness so not the ideal way to go. If Konceptus starts trading again their springs are very nice - softer than standard. My Konceptus kitted 99 is excellent.

    For a meteor spring use an early mark of meteor and original equipment...

  15. #15
    Join Date
    Nov 2008
    Location
    Preston
    Posts
    3,278
    Titan meteor spring is no. 5. I have used these in some guns but wouldn't say they were particularly soft. The spring in my HW50 is an old one out of my 22 95. Produces 11 in 22. TX mk3 springs are quite weedy so may be worth a look to see if they would fit.
    Plinkerer and Tinkerer

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •