Page 1 of 2 12 LastLast
Results 1 to 15 of 16

Thread: HW95 barrel alignment problem

  1. #1
    Join Date
    Jan 2008
    Location
    stratford upon avon
    Posts
    347

    HW95 barrel alignment problem

    Hello everyone,

    I’m hoping for some help regarding my offset barrel alignment after fitting a tuning kitty my HW95..

    The problem is that the barrel is leaning towards the left after reassembling?

    I can remember three metal shims that fitted near the breach & barrel liver bolt. I only replaced two of these from memory (one either side of the breach).

    Could the missing shim reall make that much difference?

    It may be out of my skill level to sort this out so if anyone could recommend someone to fix this I would be very greatful.

    Many thanks in advance..

    Matt

  2. #2
    tinbum's Avatar
    tinbum is offline Killer Vampire Lesbians on scooters
    Join Date
    Aug 2007
    Location
    Daarn Saaarf!
    Posts
    19,799
    You need to watch those tuning kittys!

    If there were two shims on one side it would have been for a reason, my first move would be to put them in.

    **Top Tip: The top from a bic biro is an Hw owners freind. The soft, plastic pointy clip is perfect for pushing the shim in, then wiggle the cap in the bolt hole to centralise it**
    Better to admit you walked through the wrong door than spend your life in the wrong room

  3. #3
    Join Date
    Jan 2008
    Location
    stratford upon avon
    Posts
    347

    Kitty’s

    I told myself at the time not to take it to bits 🤦♂️


    Would you happen to know the side that both shims should go on if the barre is leaning left?

    All the best,

    Matt

  4. #4
    tinbum's Avatar
    tinbum is offline Killer Vampire Lesbians on scooters
    Join Date
    Aug 2007
    Location
    Daarn Saaarf!
    Posts
    19,799
    I would put them where ther were
    Better to admit you walked through the wrong door than spend your life in the wrong room

  5. #5
    Join Date
    Oct 2013
    Location
    Ashtead
    Posts
    96
    Quote Originally Posted by barghmatt View Post
    I told myself at the time not to take it to bits ��♂️


    Would you happen to know the side that both shims should go on if the barre is leaning left?

    All the best,

    Matt
    First thought is to say putting it on the left will push the barrel to the right but then we are talking about normally parallel faces and a shim would only displace a parallel barrel by its thickness. So, second thought is that placing the shim on the right hand side will increase the gap between faces on that side by enough for the left hand side of the clamping faces to push the barrel over to the right.
    Of course I am probably completely wrong so given it is an easy matter to remove and replace them just have a go and try it and if it doesn't work change them over.
    Sorry if this isn't of much help. Oh, and none of my 95's , and I have three of them, has more than one shim on either side
    Jim

  6. #6
    Join Date
    Jan 2008
    Location
    stratford upon avon
    Posts
    347

    Fixit

    Is there anywhere I could send it/take it to to fix it?

    It was a year or two ago when I took it to bits.

    I tried SFS but they have an 18week turn around 😮

  7. #7
    tinbum's Avatar
    tinbum is offline Killer Vampire Lesbians on scooters
    Join Date
    Aug 2007
    Location
    Daarn Saaarf!
    Posts
    19,799
    Quote Originally Posted by barghmatt View Post
    Is there anywhere I could send it/take it to to fix it?

    It was a year or two ago when I took it to bits.

    I tried SFS but they have an 18week turn around 😮
    If it needs fixing then yes, but it shouldn't be too hard to figure out. Pm or ring me if you get stuck
    Better to admit you walked through the wrong door than spend your life in the wrong room

  8. #8
    Join Date
    Jan 2008
    Location
    stratford upon avon
    Posts
    347
    Quote Originally Posted by Dagwood View Post
    First thought is to say putting it on the left will push the barrel to the right but then we are talking about normally parallel faces and a shim would only displace a parallel barrel by its thickness. So, second thought is that placing the shim on the right hand side will increase the gap between faces on that side by enough for the left hand side of the clamping faces to push the barrel over to the right.
    Of course I am probably completely wrong so given it is an easy matter to remove and replace them just have a go and try it and if it doesn't work change them over.
    Sorry if this isn't of much help. Oh, and none of my 95's , and I have three of them, has more than one shim on either side
    Jim


    Many thanks Jim,

    That very kind.

    I’m going to try this evening.

    Wish me luck 😁

  9. #9
    Join Date
    Jan 2008
    Location
    stratford upon avon
    Posts
    347

    Unhappy hw95

    Thanks all for your input,

    I've taken the gun apart & the barrel is bent

    Not only that, I've managed to damage the full length slip over barrel mod..

    Any idea where i could get a new .177 breech & barrel?

    I assume they are one part?.

    Many thanks again,

    Matt

  10. #10
    Join Date
    Nov 2014
    Location
    Batley
    Posts
    1,667
    That's bad news is that, you can get new barrels delivered to your door from sportwaffen Schneider in Germany bud.

  11. #11
    Join Date
    Jan 2008
    Location
    stratford upon avon
    Posts
    347

    Hw95

    Quote Originally Posted by mattyw1987 View Post
    That's bad news is that, you can get new barrels delivered to your door from sportwaffen Schneider in Germany bud.
    Thank you..

    Ill have a route around..

    All the best,

    Matt

  12. #12
    Join Date
    Jan 2008
    Location
    stratford upon avon
    Posts
    347

    HW95 with 98 barrel?

    Sorry to trouble you again fellas..

    Am I ok to assume a 98 shrouded barrel will fit to my 95 action?

    all the best,

    Matt

  13. #13
    Join Date
    Sep 2017
    Location
    Hampton
    Posts
    291
    Should do, they are basically the same gun. Rog

  14. #14
    Join Date
    Jun 2011
    Location
    middlesbrough
    Posts
    9,062
    Yes
    LOOKING FOR A BSA ULTRA IN .177 and .25

  15. #15
    Join Date
    Apr 2012
    Location
    Retford, Notts
    Posts
    37,287
    Quote Originally Posted by tinbum View Post

    **Top Tip: The top from a bic biro is an Hw owners freind. The soft, plastic pointy clip is perfect for pushing the shim in, then wiggle the cap in the bolt hole to centralise it**
    What a lovely, useful tip from a caring, sharing chap.
    THE BOINGER BASH AT QUIGLEY HOLLOW. MAKING GREAT MEMORIES SINCE 15th JUNE, 2013.
    NEXT EVENT :- May 17/18, 2025.........BOING!!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •