Page 1 of 5 123 ... LastLast
Results 1 to 15 of 61

Thread: Best way to refinish a gun stock

  1. #1
    Join Date
    Apr 2022
    Location
    Medway
    Posts
    171

    Best way to refinish a gun stock

    As title, does anybody know how to step by step refinish a gun stock? I'd like to do a very good job or as good as I can.

    Thanks in advance.

  2. #2
    Segata is online now Has not one but two workbenches in his shed
    Join Date
    Nov 2023
    Location
    Stevenage
    Posts
    3,316
    Theres quite a few video tutorials on youtube as theres so many ways to do it.

    The one I did currenty as budgets tight is an off the shelf stain with a Wax sealer that should come up nice, that was simply strip the wood and very lightly sand to make sure the pores are open, I also used a filler matched to the wood type which in this case was Beech to fill in any dings and sanded so things blended nicely.
    The Stain required an alcohol wipe down and then it was two coats, wet and dry with high grits to make sure things are smooth, then two more coats and a light going over again with high grit.
    Wax is currently being applied, the stuff I've got is a Paste that you liberally apply and allow 4 hours to set before buffing back, there will be a few rounds of this until there is a deep satin sheen.
    You'll Shoot your eye out Kid
    Currently looking for an SMK/BAM B4-4 Rear sight or help modifying current one.
    Wanted Daisy Model 25 or Norica Commando in reasonable condition.

  3. #3
    Join Date
    Apr 2007
    Location
    Bordon Hants
    Posts
    736
    True oils is good if done properly.

  4. #4
    Join Date
    Sep 2010
    Location
    Exeter
    Posts
    36,779
    Quote Originally Posted by Targetman83 View Post
    As title, does anybody know how to step by step refinish a gun stock? I'd like to do a very good job or as good as I can.

    Thanks in advance.
    Depends what you start with & what finish you want

    all mine are now finished in matt olive green

  5. #5
    Segata is online now Has not one but two workbenches in his shed
    Join Date
    Nov 2023
    Location
    Stevenage
    Posts
    3,316
    Targetman, perhaps it's worth posting what you'd like to have the final finish as and what the stock is made from as that will help get the answers you need.
    You'll Shoot your eye out Kid
    Currently looking for an SMK/BAM B4-4 Rear sight or help modifying current one.
    Wanted Daisy Model 25 or Norica Commando in reasonable condition.

  6. #6
    Join Date
    Apr 2022
    Location
    Medway
    Posts
    171
    Thanks for the replies so far everyone, apologies it is a walnut stock, and would just like to get it looking decent, it has no dings or scratches but was previously refinished by someone else and would like to get it back to it's original state.

  7. #7
    Segata is online now Has not one but two workbenches in his shed
    Join Date
    Nov 2023
    Location
    Stevenage
    Posts
    3,316
    Should be fairly straightforward, you'll need to strip the finish, ideally with a Chemical stripper, gentle sand and wipe down with alcohol to make sure theres no contaminents left, oil liberally and wipe off with something like Danish or Linseed oil and then use an appropiate varnish or wax sealer.

    I do reccomend searching those tutorials out so you can see visually how it's done, I wouldn't use a stain in this case if you're certain its Walnut as you'll not want to darken it (some like my 25 use Beech and then darken to mimic walnut).
    You'll Shoot your eye out Kid
    Currently looking for an SMK/BAM B4-4 Rear sight or help modifying current one.
    Wanted Daisy Model 25 or Norica Commando in reasonable condition.

  8. #8
    Join Date
    Nov 2008
    Location
    Preston
    Posts
    3,278
    Hi, a walnut stock is the easiest to refinish imo. Remove all the existing and sand down to at least 400 grit ( thats as far as I go). Then get a good gun stock oil such as CCL and rub in. It'll soak in easy at first and slow down over time. Don't slosh too much on at once and remove any excess before it dries. Little and often is the best way. You won't need to overseal with wax or varnish, the oil finish will build up over time. Don't put hardly any oil in the checkering, just enough to colour the wood.
    Plinkerer and Tinkerer

  9. #9
    Join Date
    Apr 2022
    Location
    Medway
    Posts
    171
    Perfect, thank you everyone, it doesn't sound too difficult, I think even I can do it!

  10. #10
    Join Date
    May 2013
    Location
    Newton le Willows
    Posts
    1,249
    It depends on the current finish.

    If it’s oil then strip it with meths and scotchbrite pads ( fine grade will do the job ), use a nylon brush on the chequering and then clean out with a tooth pick.

    Let it dry for 24hrs, then steam any dings and if the gun is used there will be dings. Let it dry before sanding with scotchbrite pads, medium down to extra fine and then wash off with spirit.

    If not staining then the first coat should be 50/50 of chosen oil and spirit, for me this is always Alkanet oil. Leave it 24hrs and then fill the grain using the alkanet oil and 1000grit wet n dry paper, dont wipe off the slurry just leave it 24hrs before buffing it off with lint free cloth. Check it over and see if any grain needs further filling, if not then you can start the months long process of building a very nice oil finish.

    Thin coat of oil, wait an hour and buff off with lint free cloth, do this every other day for fortnight and them once a week for a couple of months. If you prefer a more satin finish then the last piece is to use xxxfine pumice powder to take the sheen back a little. She’ll be silky smooth if done well.

    Tru-oil is hideous varnish that is only fit for bar tops in the local boozer, just my opinion…

  11. #11
    Segata is online now Has not one but two workbenches in his shed
    Join Date
    Nov 2023
    Location
    Stevenage
    Posts
    3,316
    Can't stand actual Varnish myself, I used to muck about with vintage radios and it loves to discolour and flake if exposed to the Sun over time which for a Rifle is pretty much whenever it's used.
    You'll Shoot your eye out Kid
    Currently looking for an SMK/BAM B4-4 Rear sight or help modifying current one.
    Wanted Daisy Model 25 or Norica Commando in reasonable condition.

  12. #12
    Join Date
    Dec 2009
    Location
    Cheltenham
    Posts
    3,262
    My best tip is…take your time…

    (As most would also agree).

    If you have to go back to bare wood, Personally I’ve had best results from the CCL range of refinishing kits - nice that you can get the individual components as well. Be prepared to, if necessary, (as mentioned already) raise and sand back the grain, then ensure the grain is filled before you choose (if necessary) to stain it. This takes time and depends on the wood quality; the better quality being more tightly grained and in need of less prep. Palming in the oil/hardener does take many weeks to build up, but if done with patience will enhance any stock. I’ve also had success with the Napier kit.

  13. #13
    Join Date
    May 2008
    Location
    Quigley Hollow, Nuneaton
    Posts
    17,125
    Quote Originally Posted by Targetman83 View Post
    Thanks for the replies so far everyone, apologies it is a walnut stock, and would just like to get it looking decent, it has no dings or scratches but was previously refinished by someone else and would like to get it back to it's original state.
    When I've quickly refinished oiled stocks in good condition, I just scrub them down with cellulose thinner to remove the old oil and dirt and then when dry I've re-oiled them.

    If your stock has been refinished with varnish then you have the ball ache of removing the varnish before re-oiling.



    All the best Mick

  14. #14
    Join Date
    Apr 2007
    Location
    Bordon Hants
    Posts
    736
    If you have no dings or scratches a clean stock that needs a new finish then theres no need to sand anything just remove the old finish. I use cellulose thinners or gun wash with fine wire wool, then either colour the stock or have it in its natural form and either spray vanish it in matt satin or gloss or oil with a boiled linseed or true oil. With boiled linseed it takes a very long time to dry before handling, true oil you can build up to a gloss or use one or two coats for a matt or semi gloss let it fully dry and then go over with a very fine steel wool lightly and then wax. If you want it factory its usually sprayed with a lacquer in 2k or standard. To be honest there are quite a few ways to do a stock best to experiment before you try your prized piece.

  15. #15
    Join Date
    Feb 2004
    Location
    Radcliffe on Trent ,nottinghamshire
    Posts
    4,663
    just butting in here sorry :-

    Just wondering if any one as had good success refinishing Beech stocks , ive got a HW80 and a pros-port , that could do with a make over .

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •