The Challenger Arms Corporation Plainsman (pneumatic) air pistol...

[JimmieDee]

Hi Jimmie yes please if you don't mind.
ATB,
Mick.

Mick,

A 16mm x 2.5mm (R11 size) o-ring will fit as I have just measured up and put one in mine. I can pop a few in the post if you like.

All the best,
Jimmie

[Benelli B76]

Mick,

A 16mm x 2.5mm (R11 size) o-ring will fit as I have just measured up and put one in mine. I can pop a few in the post if you like.

All the best,
Jimmie

Did you find that the Nitrile and Viton rubber ones swell up from absorbing CO2 and you need to leave them quite a while before they return to a size where you can refit the cap ? I had to order a load of special ones for my C02 Plainsman.

Baz

[JimmieDee]

Did you find that the Nitrile and Viton rubber ones swell up from absorbing CO2 and you need to leave them quite a while before they return to a size where you can refit the cap ? I had to order a load of special ones for my C02 Plainsman.

Baz

Not really. It depends on how long you are going to shoot with it. At about 15 usable shots at full power per 8g cartridge, that end cap isn't going to be exposed to CO2 for long enough unless you leave the cartridge in the pistol.

[DT Fletcher]

I think you'll find that all of the American CO2 end seals are the same. The Crosman part number is 150-054 and is easily found under that number on the bay etc. I stocked up on the opaque white ones that are a harder compound which resists any CO2 and holds up to the abrasion from use.

[JimmieDee]

Thanks DT. Although a search of that number only gives this....

http://www./itm/Male-Power-Wings-pou...dB1_BHO7aaNckA

[DT Fletcher]

Thanks DT. Although a search of that number only gives this....

http://www./itm/Male-Power-Wings-pou...dB1_BHO7aaNckA

Apparently what I saw were a bunch of US listings. In any case, the best way to source common parts like this is to go through one of the major shops in the US like MAC-1, Precision Pellet, etc. They've already gone to the effort of finding the right parts that really work.

[Benelli B76]

Not really. It depends on how long you are going to shoot with it. At about 15 usable shots at full power per 8g cartridge, that end cap isn't going to be exposed to CO2 for long enough unless you leave the cartridge in the pistol.

Yes we find the maximum number of decent shots is 20 from the 8 grm, and the black rubber seals expand immediately you take off the end cap to put in the new capsule. All my CO2 pistols now have 90 degree Shore A polyurethane seals in as I buy them in bulk. The Crosman 600 seal fits a lot of different pistols, but not the Challenger which is larger.

Baz

[JimmieDee]

It looks like I will be writing an article about the Plainsman (Goodenow) pneumatic air rifle soon....

What's the going rate for one?

[JimmieDee]

DT, your bulk fill CO2 Challenger. Is that bulk fill only. Or bulk fill and pump up? Or bulk fill and 8g CO2?

All the best,
Jimmie

[DT Fletcher]

DT, your bulk fill CO2 Challenger. Is that bulk fill only. Or bulk fill and pump up? Or bulk fill and 8g CO2?

All the best,
Jimmie

It is bulk fill only and cannot be converted to pump up. I believe that the guns could be made either bulk fill or 8g cartridge.

[micky2]

Mick,

A 16mm x 2.5mm (R11 size) o-ring will fit as I have just measured up and put one in mine. I can pop a few in the post if you like.

All the best,
Jimmie

Hi Jimmie, that's a kind offer, l will pm you my address.

ATB,
Mick.