Results 1 to 7 of 7

Thread: Use of Hawke SR6 and SR12 scopes on 12fpe guns, what zero range?

  1. #1
    Join Date
    Jul 2004
    Location
    California, USA
    Posts
    1,169

    Use of Hawke SR6 and SR12 scopes on 12fpe guns, what zero range?

    I have a couple of TX200HC(.177 & .22) and have several Hawke scopes, what is the correct zero range to get the corresponding holdover points on the reticle in 10 yard increments?

    On the .22, do I zero at 30 yards at the center of the reticle to yield the holdover point above center as being 20yards followed by 40 and 50 yards for the points below the center of the reticle?

    Please advise...

    Regards,

    Tony

  2. #2
    Join Date
    Sep 2006
    Location
    Southend, Essex
    Posts
    2,497
    Download the Hawke Ballistic Reticule calculator from here

    www.hawkeoptics.com/brc/index.htm

    Just follow the instructions and it will calculate and display all you need.

    It is designed for the SR6, SR12 and MAP reticules but I find it is is usefull for calculating aimpoints for just about anything.

  3. #3
    Join Date
    Jul 2004
    Location
    California, USA
    Posts
    1,169

    Thanks! nt

    Quote Originally Posted by Gavin2593 View Post
    Download the Hawke Ballistic Reticule calculator from here

    www.hawkeoptics.com/brc/index.htm

    Just follow the instructions and it will calculate and display all you need.

    It is designed for the SR6, SR12 and MAP reticules but I find it is is usefull for calculating aimpoints for just about anything.





    12345

  4. #4
    Join Date
    Apr 2006
    Location
    coventry
    Posts
    384
    Quote Originally Posted by Gavin2593 View Post
    Download the Hawke Ballistic Reticule calculator from here

    www.hawkeoptics.com/brc/index.htm

    Just follow the instructions and it will calculate and display all you need.

    It is designed for the SR6, SR12 and MAP reticules but I find it is is usefull for calculating aimpoints for just about anything.
    this will depend on your velosity(foot lbs) over here were the limit is 12ftlb, would i be wright saying you have no such restrition on airguns over in the states

  5. #5
    Join Date
    Jul 2004
    Location
    California, USA
    Posts
    1,169

    Thanks, correct, no fpe limits here in the USA

    Quote Originally Posted by simmo 1198 View Post
    this will depend on your velosity(foot lbs) over here were the limit is 12ftlb, would i be wright saying you have no such restrition on airguns over in the states
    my TX200HC's are both set up at sub 12fpe with UK springs in them...on the other side of the spectrum I do have lots of FAC air rifles pushing up to 200fpe(Dragonslayer .50)

    Regards,

    Tony

  6. #6
    Parabuteo is offline My Chrony has bought it a couple of times...
    Join Date
    Mar 2006
    Location
    Southampton
    Posts
    6,061
    Nick Jenkinson advocates zeroing a 11.5fpe +/- .177 airgun at 40yds (SR6).

    I have done this, continue to do so, and it works. It gives quite a nice margin for error at typical airgun hunting ranges.
    I'm a maggot in another life you know

  7. #7
    Fluffybuck is offline Member of the .25 cal fan club
    Join Date
    Feb 2006
    Location
    Cambridge, Cambridgeshire
    Posts
    8,343
    The Hawke BRC has several pre-set reticule and calibre options.
    However, you will need to change the "E.D Value" box to the correct ballistic coefficient of the pellet you're using to get a good trajectory match.
    The default ED Values do not equate to your average pellets in the respective calibres.
    You may well find (as I have) that 7x mag is a better choice for most .22 pellets at 12ftlb, rather than the 6x that is recommended.
    Last edited by Fluffybuck; 15-12-2007 at 09:11 PM.
    .

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •