Any Rekord trigger experts in?

[JerryD]

I had a Rekord that was like that: the first stage pin in the trigger had dropped out. The trigger blades themselves aren't made of great material.

Yuo can see the pins in this animation:

https://youtu.be/_BlQRRciXMQ

The only way to check is to remove the trigger by knocking out the trigger pivot pin. If they have fallen out then it's a new blade to fix it.






.

[Daveo]

I had a Rekord that was like that: the first stage pin in the trigger had dropped out. The trigger blades themselves aren't made of great material.

Yuo can see the pins in this animation:

https://youtu.be/_BlQRRciXMQ

The only way to check is to remove the trigger by knocking out the trigger pivot pin. If they have fallen out then it's a new blade to fix it.






.

Thanks I will certainly check that. Something feels very wrong here

[TonyL]

Firstly, does the trigger feel worse now than before working on the gun? If so, it may be that the sear at the bottom is catching on some stock material. Maybe? Also, are the trigger guard retaining screws screwed up too tight? Slacken them off a little and see how it feels.

Also, remove the trigger unit and give it a good soaking in some degreaser / solvent. It may be that the gunky original factory grease is still in there and gone well hard and even more gunky. Allow to drain and dry and then apply a little light machine / gun oil.

Then.....that small grub screw at the front bottom.....as stated above it controls the second sear engagement. Screwing it in, clockwise, lightens it. Only do it in tiny increments and keep checking that there is solid engagement through the hole as above.

The larger allow screw behind the blade controls the weight on the spring. Again, as described above, don't screw it out TOO far as the trigger will go floppy.

Great advice up above re doing many of the adjustments with the unit out of the gun, but don't be tempted to go too light. A safe, consistent and dependable trigger is what you want and not an unsafe / overlight / unpredictable one.

Hope this helps and be sure to report back in.

[johnbaz]

Don't know if you're on Facebook but there's a lad on there that is a wizz with the Rekord unit, He's called Luke Jolly and will service them and make them soooo smooth!!

He's also a nice lad too unlike half of the eejits on there that force advice on things they've clearly never used or owned!!


John..

[Blackmax]

I think you'll find it's the trigger tension spring that sits under the alloy screw behind the trigger.

When overtightened for a protracted period the spring crushes, deforms and becomes ineffective.

If the sear engagement is out if adjustment as a singular fault you still get a distinct second stage but there's creep into the second stage until the sear releases.

Any problems pm me and I'll chat it over with you.

[FPoole]

Can the Torx screw be wound in, or is it out on the Rekord, until the trigger releases in the first stage? I assume the heaviness is from the weight of pull screw being too far in.

[PhatMan]

Daveo,

Remove trigger unit, clean and lube as others have said.

The is a round hole in the trigger case, and through it you can see how the sears engage.

You can cock the trigger by pressing down the top sear with the end of a Bic biro or similar non-metal item until it clicks

I would start by screwing in the weight adjuster a few turns to get the pressure up a bit.

I would back out the torx screw a few turns, then looking at the sears, see how they progress as you pull the trigger.

Adjust the torx screw until you have a crisp let off, then back a turn. This is to give you some margin when the trigger is in the rifle and under tension from the main-spring.

Return the trigger to the rifle, and then fine adjust the torx screw to give the let off you like - you do not have to put the stock back on while you are doing this adjustment, but please be careful !!

To get the ultimate cherry on the cake, send the trigger to Mr. Luke Jolly - it will return with a safe pull, set at 6 oz, and will be crisper than a very crispy thing

Have fun & a good weekend

Best regards

Russ

[thisisdonald]

Don't know if you're on Facebook but there's a lad on there that is a wizz with the Rekord unit, He's called Luke Jolly and will service them and make them soooo smooth!!

He's also a nice lad too unlike half of the eejits on there that force advice on things they've clearly never used or owned!!


John..

+1 for Luke Jolly... he showed me how to tune the rekord trigger a couple years ago.. he really devoted a lot of time and effort to these triggers. I wouldn't hesitate to send him my trigger for a tune/rework... like John said, get him through Facebook.