Results 1 to 14 of 14

Thread: An Airgun O Ring database

Threaded View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Dec 2003
    Location
    Cambridge UK
    Posts
    7,135

    An Airgun O Ring database

    Here is my database. It may help someone. I offer it in good faith but as it was largely compiled from other peoples' data I cannot vouch for the information. If more info is added to the thread I will add it to the database.
    Cheers, Phil

    Hmmm ... all formatting lost when pasting the table. Any tips on pasting a table ? I offer now my best attempt at shifting text around:

    MAKE
    MODEL PART O RING
    A&M cylinder fill probe for HW100 4mm id x 2mm cs
    Air Arms Series 100 Firing valve and filler valve body: parts AA3810 (U ring), AA1065 (O ring)
    U ring 18x28x6
    O ring AS212
    Air Arms S200
    Loading bolt probe Cz014 3 x 1 (.177 & .22)
    Airtube 21 x 2
    Firing valve end seal 6.5 x 2
    Magazine rings .177 12 x 3.5
    .22 11 x 3.5

    S400 / 410 AIR ARMS PART AA Code O RING
    S400/410
    Cylinder seals (2) RN234 BS213
    Magazine ring S556 22 x 1.5
    New style external filling seals (2) S474 12 x 2
    Old style filler valve Dowty seal 1/8
    Internal filling seals (2) S484 12 x 1.5
    Pressure gauge seal RN219-9 BS011 but note that our 410 is not a BS011 … more like a flat rubber washer
    Loading bolt buffer S650 8 x 1.25
    Barrel seal .22 S538 BS009
    Transfer port seal S427 6 x 1
    Pressure gauge mount lower seal S427 6 x 1
    Pressure gauge upper seal (bolt) S536 BS008
    Barrel seal .177 FP121 1.5 x 4.5
    Filling valve internal seal S327 BS005 90 shore


    ProSport/TX200/ TX200SR Breech seals 6.02id x 2.62 BS108
    SR buffers
    TX compression tube end bolt 1.6 x 22.1
    Benjamin 262 pistol Cylinder end cap BS115 maybe polyurethane
    Loading probe .22 BS004
    Brocock Enigma See post 10
    BSA
    Ultra Pellet probe ?? .22 = 1.5 x 3
    Pellet probe ?? .177 = 1.5 x 2 BS008
    Goldstar SE Pressure gauge BS106 70/90 shore may fit but true size is 70 shore 3mm id x 3mm cs (infor from J Bowkett)
    Airsporter Piston seal 21.82id x 3.53cs BS212
    Mercury Piston seal 21.82id x 3.53cs
    Breech seal 12mm od, 8mm id x c. 4mm BS212

    Meteor Piston seal 18.64id x 3.53cs BS210
    Spitfire Filling probe BS008 x2
    Crosman 2200 / 766 / 760 Valve: outer BS111
    Valve cap (inner) BS012
    140 Valve body outer BS111
    Valve body inner BS012
    Valve cap outer BS011
    Valve cap inner Quad ring (x ring) Q008 or BS008 or 4mm x 2mm

    Breech bolt BS006?
    Transfer port seal Poly pipe 6mm
    Daisy 880 Loading probe. 1mm x 4
    Daystate All PCP Loading probe .177 BS003
    Loading probe .22 BS004
    Loading probe .20 BS004
    Loading probe .25 BS005
    Magazine O ring BBS suggests Sealforce in Dundee as supplier. 25 x 1.5

    Filler valve stem BS006 is mentioned


    Diana / Original / RWS Break barrels Breech seal 8 x 2.5

    Orig 66 Breech seal BS109 fits
    Orig 45 Breech seal BS110 2.62 cs, c. 13.3 od
    FWB Sport Breech seal O ring
    Note: Some were apparently larger at about 15.7mm od x 10.9mm id and 2.4mm section. A German metric 011-25 (11mm id x 2.5 section) is close but a BS 111 will fit. Maybe ser No. upto 5000 Metric 10mm id x 3mm section. Thought that this is for ser No. over 5000
    Huggett moderator 13mm id x 2.5mm cs

    Parker Hale Phoenix MK1/MK2 Air bottle O ring BS013

    Sharp Innova Exhaust valve (+9/32 ball) BS007
    Steyr LG100 / 110 reg interface and transfer port 6x2
    inside cylinder 7x2
    rear of filler 13x2
    interface to firing valve 24x2
    block cocking lever 2.9x1,8
    internal loading port 5.28x1,78
    inside front stock 36x2
    small regulator 3x1.5
    Large regulator 8,92x1,83
    Inside top of reg 1,5x1
    Theoben Fenman Breech seal, but with a small cut out on outer edge. But works without? BS109
    Walther LGR Breech seal x 2. Original is not an O ring but these will fit BS010
    Webley Tracker Loading tap BS013 10.82 x 1.78
    Weihrauch HW45 Breech seal: #009 5.58 x 1.78 new Old: 1.5 cs 5mm id
    Cylinder to end block: 19.00 x 1.50
    Cylinder to breech block 5.00 x 1.50
    HW90 The two o-rings show 23,813 - 2,381 mm / imperial 15/16" - 3/32"
    The packer ring 22,225 - 2,381 / imperial 7/8" - 3/32"
    You may order at T.W. Chambers as follows:
    o-ring sealing / HW-no. 2030 / Chambers no. OR066
    back-up (packer) ring / HW-no. 2031 / Chambers no. PW128

    HW100
    *Alternatives Air cylinder seal BS005
    Fill probe 2.57mm x 1.78mm BS005
    A&M cylinder fill probe 4mm id x 2mm cs
    Cylinder clamp 2682C 37.1 x 1.6
    Barrel clamp 2682B 15.6 x 2.5
    Magazine 2603A* Alternative size 32 x 2
    Adaptor A 2704 13 x 2
    Adaptor B 2703B 2.57 x 1.78
    Valve stem 2655D 3 x 1.5
    Breech block main recommended 2658 12 x 1.2 (12 x 1)
    Breech/probe seal .22 2659A* 5.5 x 1
    Breech/probe seal .177 2659A* 4.5 x 1
    Hugget shroud 14 x 1.5
    Probe buffer 2618A* 4 x 1.5
    Main valve inlet 2665D 2.57 x 1.78
    Main valve outlet 2666 7 x 1.5
    Main valve internal recommended 2 x 2
    N/A (2.57 x 1.78)
    Regulator piston 2668 7 x 1.5
    Tension adjuster (sometimes omitted) 2672 10 x 1.5
    Barrel 2679 8 x 1.5
    HW100 also see post 12

    "O" rings and part numbers for the FX "Third Generation" pump. Not my data but added in good faith.
    U-006 Urethane 90 durometer Part number 30
    BN-009 Buna Nitrile 70 durometer Part number 40
    BN-106 Buna Nitrile 70 durometer Part number 39
    BN-117 Buna Nitrile 70 durometer Part number 35
    23 x 1 mm Buna Nitrile 70 durometer Part number 25
    2.5 x 1.5 mm Buna Nitrile 90 durometer Part number 38
    9.3 x 2.4 mm Buna Nitrile 70 durometer Part number 27
    9.3 x 2.4 mm Buna Nitrile 90 durometer Part number 37
    11.6 x 2.4 mm Buna Nitrile 70 durometer Part number 28
    21.3 x 2.4 mm Buna Nitrile 70 durometer Part number 36
    18 x 2.5 mm Buna Nitrile 90 durometer Part number 24
    20 x 2.5 mm Buna Nitrile 70 durometer Part number 31
    The first four are Standard "O" ring sizes. The next two are regular Metric as well as the last two. The others are Japanese Metric, hence the 2.4 mm cross-section size. It is very important to install parts numbers 35 and 31 in EXACTLY the right sequence, or your pump will not operate properly. Lubricate them while installing and afterwards with diver's silicone grease. Do not use any petroleum based greases, PERIOD.
    I could not get part number 37 in 90, so I used 70 in its place. It might not last quite as long, but until I can get the proper one, it will do. The most important one to get as shown, is the very first one. If you get anything else, it will blow out real fast, like in two or three fillings. Trust me on that one.


    Cheers, Phil
    Last edited by Phil Russell; 23-02-2020 at 03:44 PM. Reason: update2 Feb 2019

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •