Daystate tactical stock.

[where's it gone]

Mine is that same, I only bought it to fit studs but I've kept the original walnut stock as it's a lovely stock, I dont mind the sticky side of it at moment but it don't half pick up fluff etc and looks shabby, I'm sure halfords do a rubber type spray but I to will be keeping an eye on this thread for any advice, I guess the rubber stuff on my stock is going to get worse ,

Here's the reply I got from Daystate.
Unfortunately it sounds as though the molecular structure of the rubber within the stock has began to break down, and like all rubber returning to its natural state irrespective of composition, hence the stickiness. While I cannot for sure say why this is happened to yours, the common cause is petrochemical contamination, such as oil, cleaner, detergent, high levels of UV etc..

The most likely rectification method is to have your stock refinished by a third-party, or clean off the old rubber with solvent, and re-coat with rubber spray found that many Motor factor resellers, shops etc.

We do not have any replacement stocks, but likely you will find one via social media or other areas should you need, or do it yourself as there are many guides on the Internet.

[madcarlos]

Here's the reply I got from Daystate.
Unfortunately it sounds as though the molecular structure of the rubber within the stock has began to break down, and like all rubber returning to its natural state irrespective of composition, hence the stickiness. While I cannot for sure say why this is happened to yours, the common cause is petrochemical contamination, such as oil, cleaner, detergent, high levels of UV etc..

The most likely rectification method is to have your stock refinished by a third-party, or clean off the old rubber with solvent, and re-coat with rubber spray found that many Motor factor resellers, shops etc.

We do not have any replacement stocks, but likely you will find one via social media or other areas should you need, or do it yourself as there are many guides on the Internet.

Thanks for the info but it's quite a common thing with these stocks, Saying that I had a lovely Joe rocket motorcycle jacket that i bought from M&P motorcycles in Swansea some years ago, It was a cracking jacket and in all fairness it was waterproof. Anyway I decided to remove the back armour to fit in another jacket which was more suited for the winter only to find that the back protection had seemed to have melted like a 1000 black Jack's that had been munched by a donkey, Jesus it was awful, Went straight in the bin, Was gutted as it was a lovely jacket to,

[madcarlos]

Just done a quick wipe over of the guns and came to my air ranger , The stock on it at moment is the above, Rubber coated, Its quite messy now , Picking all bits of fluff etc, I'm gonna stick the walnut one back on for now but as the above, Any quick remedies.

[Jesim1]

Sorry, it's a stock refinish I'm afraid, they tend to do about ten years or so before going, but when they start, that's it

[madcarlos]

Sorry, it's a stock refinish I'm afraid, they tend to do about ten years or so before going, but when they start, that's it

It's ok now I've got the minelli one back on and fixed studs to it yesterday , Only bought the other to fix studs and to keep the other stock nice , The gun is looking lovely again and someone is supposed to be picking the other one up later, The tackiness was ok it's the stuff that sticks to it and makes it look shabby. I was tempted to get it dipped but I got to stop keeping stuff just for the sake of it, Thanks anyway,

[Neil54]

The tackiness can be removed using isopropyl alcohol and a lint free cloth or a green pan scrubber.

I always understood it was the plasticser leaching out of the material.

I have an army sleeping bag and the waterproof bottom stuck to a sleep mat.

[madcarlos]

The tackiness can be removed using isopropyl alcohol and a lint free cloth or a green pan scrubber.

I always understood it was the plasticser leaching out of the material.

I have an army sleeping bag and the waterproof bottom stuck to a sleep mat.

Thanks for the advice, If this chap dont turn up today then I may keep it and have a play,

[Gunner786]

Here's the reply I got from Daystate.
Unfortunately it sounds as though the molecular structure of the rubber within the stock has began to break down, and like all rubber returning to its natural state irrespective of composition, hence the stickiness. While I cannot for sure say why this is happened to yours, the common cause is petrochemical contamination, such as oil, cleaner, detergent, high levels of UV etc..

The most likely rectification method is to have your stock refinished by a third-party, or clean off the old rubber with solvent, and re-coat with rubber spray found that many Motor factor resellers, shops etc.

We do not have any replacement stocks, but likely you will find one via social media or other areas should you need, or do it yourself as there are many guides on the Internet.

That's about the usual level of customer service from Daystate.