Results 1 to 14 of 14

Thread: Vintage air pistol box repair - a couple examples

  1. #1
    Join Date
    Sep 2013
    Location
    Wainfleet
    Posts
    231

    Vintage air pistol box repair - a couple examples

    1) A while back, I was sent a boxed pre-war Webley Mark I, for the purpose of rebuilding the gun and to repair the box as best possible.
    Permission from the owner was received to post the box repair.

    The lower tray was in pretty good shape, and only required gluing and reinforcing of the corner seams, however, the lid required a bit more attention - one end was completely missing.

    http://i649.photobucket.com/albums/u...Web-box-01.jpg

    A piece of the appropriate gauge of cardboard was carefully cut, fitted, and glued into place.

    http://i649.photobucket.com/albums/u...Web-box-02.jpg

    http://i649.photobucket.com/albums/u...Web-box-03.jpg

    A piece of very slightly yellowed, older newsprint paper was then glued in place in an attempt to replicate the inside liner paper.

    http://i649.photobucket.com/albums/u...Web-box-04.jpg

    I was unable to source any sort of raised pattern paper that would even come close to replicating the original cover paper, but after some experimentation, I ended up using a photocopied

    panel from one of my own early Webley boxes, and enhanced the colour to my satisfaction. While the end result is not a raised pattern, it does a pretty good job of matching up visually.

    The outer covering is started inside the box, to match the original wrap over, and then up and around to the top of the box. In an effort to avoid too much of a tell-tale clean edge at

    the top of the box, the top edge of the new paper was scuffed up a bit with a small wire brush, giving it a little bit of an aged look. Not perfect, but certainly a vast improvement over

    what it was.

    http://i649.photobucket.com/albums/u...Web-box-05.jpg

    http://i649.photobucket.com/albums/u...Web-box-06.jpg

    The completed box lid. The owner was very pleased with the restoration.

    http://i649.photobucket.com/albums/u...Web-box-07.jpg

    http://i649.photobucket.com/albums/u...Web-box-08.jpg


    2) This is how I went about restoring the lower tray of the box for a vintage Sears Ted Williams Match Pistol.

    The lower part of the box was heavily water damaged with muddy or rusty water, and then subsequently generously covered in green duct tape, to hold the failing box together. The duct

    tape was partially dried out and impossible to remove without tearing the box cover paper, and all that ugly green duct tape just had to go. The following pics show the progression of

    the restoration:

    1) The inner liner had almost completely lifted due to the water damage. As the duct tape peeled off the outer cover paper, it lifted the rest of the inside liner away from the box.

    2) The remnants of the outer covering - very little of the original black paper showing through all the duct tape adhesive residue. I should have taken a pic of the box prior to starting

    the removal of the tape, and cover paper, but it never occurred to me until after the the box was stripped.

    3) The stripped box. the original corner reinforcements were re-glued in preparation for the restore. You can see the rust coloured staining in the upper RH corner.

    4) The new inner liner paper has been glued in place.

    5) The new outer covering paper has been glued in place.

    6) Last but not least, the new bottom covering paper has been glued in place. Looks almost as good as the day it came from the factory.

    Interestingly enough, the gun did not suffer any water damage, so I can only surmise that the gun was not in the box when the water damage occurred.

    http://i649.photobucket.com/albums/u...cs/BR-001a.jpg

    http://i649.photobucket.com/albums/u...s/MVC-370F.jpg

  2. #2
    Join Date
    May 2007
    Location
    Boston
    Posts
    1,031
    Hi a very nice job you have done there, well done with the webley box.

  3. #3
    Join Date
    Mar 2010
    Location
    Rossendale and Formby
    Posts
    5,606
    Excellent cardboard engineering - well done!

    What glue did you use - PVA?
    Rossendale Target Shooting Club. Every Tuesday and Thursday evening 7 - 10pm.

  4. #4
    Join Date
    Feb 2006
    Location
    Stevenage, Hertfordshire
    Posts
    5,110
    Excellent job, big Internet High Five to you.






  5. #5
    Join Date
    Mar 2006
    Location
    City of London
    Posts
    9,896
    Very interesting photo essay, Len. Thanks. Superb de-knackering work that obviously took a lot of skill and patience.

    Makes my own recent efforts to strengthen a Mk1 box lid using 3M clear archive tape at the corners look very crude.
    Vintage Airguns Gallery
    ..Above link posted with permission from Gareth W-B
    In British slang an anorak is a person who has a very strong interest in niche subjects.

  6. #6
    Join Date
    Feb 2001
    Location
    Winchester, UK
    Posts
    15,430
    Nice job, Len.

  7. #7
    Join Date
    Jan 2014
    Location
    Newcastle
    Posts
    98
    Very nice work - thanks for taking the time to document the repairs.
    Is always interesting to see ways to restore worn items but I've not seen a guide for box repair before.


    Cheers,
    Pete

  8. #8
    Join Date
    Jun 2000
    Location
    Basingstoke, U.K.
    Posts
    6,941
    Len,

    You are indeed a man of many talents. I wish you lived nearer!

    Kind regards,

    John

  9. #9
    Join Date
    Dec 2013
    Location
    solihull
    Posts
    304
    Brilliant job

    I can fix wood, metal and plastic, wouldn't even occur to me to try repairing a box, top job!!!

    Now I have a scope box that's looking a bit dog eared...

  10. #10
    Join Date
    Sep 2013
    Location
    Wainfleet
    Posts
    231
    Thank you for the kind words, gentlemen.

    What glue did you use - PVA?
    I used a cabinetmaker's liquid glue, applied with flat toothpicks, for repairing the cardboard, such as the corners of the box, and gluing in that end panel on the Webley box.
    A product called "UHU Stic" was used for fastening the paper liners, and paper outer coverings.

  11. #11
    Join Date
    May 2004
    Location
    Ashby de la Zouch
    Posts
    2,542
    Nice job indeed Len and very useful post

    thanks
    John
    hold me back !!

  12. #12
    Join Date
    Mar 2010
    Location
    Rossendale and Formby
    Posts
    5,606
    Quote Originally Posted by Leonardj View Post
    Thank you for the kind words, gentlemen.


    I used a cabinetmaker's liquid glue, applied with flat toothpicks, for repairing the cardboard, such as the corners of the box, and gluing in that end panel on the Webley box.
    A product called "UHU Stic" was used for fastening the paper liners, and paper outer coverings.
    Thanks for the information.

    I have tried PVA with some success but I will try to find a cabinetmakers liquid glue - do you have a brand name I could look for?
    Rossendale Target Shooting Club. Every Tuesday and Thursday evening 7 - 10pm.

  13. #13
    Join Date
    Jul 2006
    Location
    sheffield
    Posts
    6,719

    Thumbs up

    Smashing job!!

    I had a Webley Senior box given to me by a nice chap on facebook!!

    Pic 1

    Pic 2



    Cheers, John
    for my gunz guitarz and bonzai, see here
    www.flickr.com/photos/8163995@N07/

  14. #14
    Join Date
    Sep 2013
    Location
    Wainfleet
    Posts
    231
    Quote Originally Posted by zooma View Post
    do you have a brand name I could look for?
    This is the glue that I used - it is made in Canada exclusively for this retailer.
    http://www.leevalley.com/en/wood/pag...10,42965,45104

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •