Hi
I used a hair dryer and lots of kitchen roll
Then sweated it out over a couple of days
Letting it cool down seems to help get the oil to the surface
Think a paint stripper would be too much
Cheers ian
I'm renovating an old BSA Breakdown model but the front of the stock almost half way to the pistol grip has years worth of oil grease etc well soaked into it and I'm not too sure about the best method of getting rid of this. I'm reluctant to soak in Acetone as I've been told this could dry out the stock too much and leave it liable to cracking so I'm stuck really. I've seen on YouTube guys heating the stock with a heat gun etc but I would value advice from you experts on here before I do something and cause irreversible damage....Thanks.
Remember, it is the strongest character that God gives the most challenges.
Hi
I used a hair dryer and lots of kitchen roll
Then sweated it out over a couple of days
Letting it cool down seems to help get the oil to the surface
Think a paint stripper would be too much
Cheers ian
I have had a good result with hot water and normal clothes washing powder, dipping the area in the solution and wiping it with a rag many times but obviously this won't work with any lacquer or varnish over the area.Dont let the wet wood dry in heat.
Lewis Potter in his book on general gunsmithing recommends immersing the oil sodden end of the stock in petrol for a few hours.
Take it out and let it dry. Repeat as necessary. I have done this myself with a cut off plastic lemonade bottle half full of petrol.
It works very well , even after one treatment. It can be completed in a single day
Just do it outside well away from anything important.
When done give it a good scrub with soapy water and let dry. Lightly sand it and give it some coats of Truoil.
Best not re-use the petrol in your motor mower afterwards !
Pete
Soak affected area in Acetone.
When I die don't let my wife sell my guns for what she thinks I gave for them!!!
Peter, I started to soak the front of the stock in Acetone but it almost immediately went white so I panicked, I thought I would be left with the stock in two shades so I let it dry then carefully rubbed it down to get the whole stock all the same colour again. ? Won't Acetone leave the stock too dry and liable to crack ?
Last edited by vbull; 13-10-2021 at 11:01 AM.
Remember, it is the strongest character that God gives the most challenges.
Yep unfortunately Acetone does leave a tide mark but it does remove the oil which is the object of the exercise. Refinishing the stock comes later. As for cracking I assume you are going to refinish the stock with "proper" oil. If you are after a magic potion which will remove oil but leave the stock finish unmarked I fear I cant help you.
When I die don't let my wife sell my guns for what she thinks I gave for them!!!
Just thought I'd give an update and at the same time ask if anyone has any new ideas. I opted for what I thought would be the easy way to do this and soaked the front of this BSA Breakdown stock for 24hrs in Acetone. One or two BBS members advised me not to soak in Acetone but anyway..... pulled it out, washed and dried it but apart from the chemical leaving a tide mark, which was quite easily removed, the Acetone made little difference, perhaps a shade or two but not much so I then decided to gently sweat it out with a heat gun and the oil just kept coming and coming to the surface in minute amounts which I wiped off with bog paper, but it's a bit like pulling teeth and life is too short.. I've spent hours today doing this and still need to spend many many more hours with this method. As you can see, I've attached some pictures showing the problem, any new ideas or suggestions very welcome. Incidentally, the Acetone was good stuff rated at 99%..
https://flic.kr/p/2mB7p9o
https://flic.kr/p/2mB58NM
https://flic.kr/p/2mB423Y
https://flic.kr/p/2mB58Yg
https://flic.kr/p/2mAYN8o
https://flic.kr/p/2mAYNcb
Remember, it is the strongest character that God gives the most challenges.
Your pictures look like the problem might be iron (rust) staining, rather than oil, in which case neither acetone or any other solvent will shift it. Iron stains can be removed by treating with oxalic acid solution. Alternatively, you can get something call "bar keepers friend" off the Bay which is claimed to shift iron and other stains from wood.
Last edited by vbull; 15-10-2021 at 11:53 PM.
Remember, it is the strongest character that God gives the most challenges.
Looks like a normal result of a bit careless wiping of oil on the action with an oil yrag, and the rag has just gone onto the wood, or ..maybe leached out of the chamber / triggerguard area as the gun has stood upright and soaked in. I would say the former as so even.
ATB, Ed
Thanks for the suggestions...
Remember, it is the strongest character that God gives the most challenges.
I used Oxalic acid crystals dissolved in warm water and applied to the spot with soaked cottonwool, Can also be mixed to a bath and soaked if the staining is particularly bad, It removes old dried oil a treat!!
The crystals can be had off fleabay too
John
for my gunz guitarz and bonzai, see here
www.flickr.com/photos/8163995@N07/